Mandam MWC Series Instruction Manual Download Page 10

10 

 

linkage. The rolled attached to the front three-point linkage should feature side-marker and 
reflective  lights.  If  the  tractor’s  headlights  are  not  visible,  their  equivalents  should  be 
installed on the machine. 

 

While transporting, do not exceed the speed, which is: 

 

up to 20 km/h on smooth-surface (asphalt) roads, 

 

6-10 km/h on field or sett paving roads, 

 

up to 5 km/h on bumpy roads. 

Travelling speed must be adapted to the road and the existing conditions so that the roller 
cannot jump on the tractor suspension system and excessive loads on the machine frame 
and the tractor suspension system can be avoided. 
Act with due caution when passing and overtaking or travelling at  curves. The permissible 
width of the machine travelling on public roads is 3.0 m. 

 

WARNING!

 

Any failure to observe the above rules may pose hazard to the 

operator and other people. It may result in damaging the machine as well. 
The  user  shall  be  liable  for  any  damage  caused  by  the  failure  to  observe 
the rules! 

3.4.

  Description of residual risk 

Mandam Sp. z o. o. act with due diligence to eliminate the risk of accidents. However, 

there is some residual risk that may result in an accident. The greatest risk is posed: 

 

if the machine is not used according to this manual, 

 

if  the  machine  is  operated  by  persons  under  age,  disabled  or  intoxicated  (under  the 
influence of alcohol or drugs), 

 

if persons or animals are present within reach of the machine, 

 

if caution is not paid during transport and maneuvering with the tractor, 

 

if persons are standing on the machine or between the machine and the tractor when 
the engine is running, 

 

during operation when operation guidelines are not followed, 

 

when travelling on public roads. 

 

3.5.

  Residual risk assessment 

 

Residual risk may be reduced to a minimum provided the following recommendations 

are applied: 

 

operate the machine carefully and without rush, 

 

read the manual carefully, 

 

keep clear from hazardous zones, 

 

it  is  forbidden  to  stand  on  the  machine  or  be  present  in  the  working  zone  when  the 
engine is running, 

 

perform maintenance in accordance with safety rules, 

 

wear safety clothes and a safety helmet while working under the machine, 

 

prevent unauthorised persons from accessing the machine, in particular children. 

Summary of Contents for MWC Series























Reviews: