SLIM-3X3 cont page 2
FIXED TRANSMISSION TIME:
( 2 second transmission even if you release the button)
To enable/disable this option do the following:
1a - hold buttons
1
and
3
until ONE OF THE LED TURN ON
2a - release both buttons ( LED TURN OFF)
5a - hold button
S
until the red led turns ON followed by 2 flashes on the GREEN led
3a - again hold buttons
1
and
3
until ALL LEDS TURN ON
4a - again release both buttons
CHANNEL MODE
: (the code is the same but the channel changes with the BUTTON selected.)
NOTES : the unit is originally sold with NO CODES IN MEMORY
2 - hold buttons S and 2 until the red led starts flashing this is followed by a flash on blue and green leds
HOW TO SET FACTORY DEFAULT
1 - hold buttons
1
and
3
until ONE OF THE LED TURN ON
OPTIONAL FEATURES
NOTES
: -repeating any of the two sequences will toggle these two options ( the generation of a random code only happens when SETTING this mode)
- every time you set or reset the channel mode all codes are automatically erased
1
2
3
3
1
1
1a - hold buttons
1
and
3
until any one OF THE LED TURNS ON
2a - release both buttons ( LED TURN OFF)
5a - press and hold button
1
until the LED START RUNNING
3a - again hold buttons
1
and
3
until ALL LEDS TURN ON
4a - again release both buttons
6a - this indicates that while holding button 1 the code is continuously incremented. The longer the hold
the higher the code , with each flash incrementing the code by 256 counts. A maximum of 65000 codes are generated before re-starting from 0.
Releasing the button at any point will store the code on the previously selected button . At the end the green Led will give 2 SHORT FLASHES
1 2
3
3
1
1
S
S
2
1
3
1&3
S
2
1
3
1&3
+
S
2
1
3
1&3
S
2
1
3
1&3
+
in this mode BUTTON S sends Ch1 , 2 = CH 2 , 3 = CH 3 and 1= CH 4
To enable/disable this option do the following
.
note: If the red led flashes 3 times it means that the antenna of the MASTER remote is not close enough.
Try and change the position of the MASTER transmitter to improve the irradiation pattern
HOW TO TURN THE SLIM- QUATTRO INTO A 4 REMOTE CHAMELEON
1
2
4
3
3&4
If you require that your SLIM QUATTRO BECOMES A MULTI CODE TRANSMITTER capable of learning and emulating the codes of
up to 4 diverse remote controls , follow the instructions below:
B
- by entering the code manually using a 5 digit number
b.1 - press and hold button 2 until the red led turns on
b.2 - Release the button
b.3 - using buttons 3 (-
I
- increment ) and 4 (-
S
-step) enter a 5 digit decimal number representing the code
3 - press and hold the button where you wish to store the new code until the red led starts flashing
1 -
Simultaneously
press BUTTONS 3 and 4 until the RED led turns ON
2 - Release both buttons
1
2
3
4
3.1 - bring the antenna section of the transmitter to be copied (MASTER transmitter)
close to the buttons 3 and 4 of the learning transmitter.
3.2 - Press the button to be copied on the MASTER transmitter
and observe that the RED stops flashing indicating that the
learning transmitter is trying to analyze the incoming code.
3.3 - keep transmitting . If successful the unit will flash once (for 1 Second)
examples:
code 12345 enter
I S , II S, III S, IIII S, IIIII S
where I = INCREMENT (BUTT 3) and S= STEP (BUTT 4)
1
2
3
4
5
code 00438 enter
S , S, IIII S, III S, IIIIIIII S
where I = INCREMENT (BUTT 3) and S= STEP (BUTT 4)
0
0
4
3
8
or
Important Note -TO CLEAR all the settings to FACTORY DEFAULT instead of the above A, B or C simultaneously
press and hold BUTTONS 3 and 4 again until the RED flashes ONCE.
or
SLIM-QUATTRO (cont) - page 2
C
- by randomly generating the code
c.2 - Release both buttons
c.1 - To record a random code (only MAMI SMART) hold BUTTON 1. While holding the button the code is continuosly
incremented. The red led will flash once to indicate that the count was incremented by 512 codes. A maximum
of 65000 codes are generated before restarting from 0.
1
2
4
3
4(STEP) / 3(INC)
M000064
