background image

5

INSTALLATION INSTRUCTIONS

Read these instructions carefully before you install the machine. The installation should be carried out by a
qualified person who is familiar with all local codes and ordinances for electrical connections. Incorrect
installation may cause damage and/or injury. If the integrity of the machine is in doubt, do not use it. Call
your dealer for qualified assistance.

The dryer can be installed in any room with a hard floor. Do not install it on carpeting with heavy pile.

Make sure the air vents on the front and rear of the machine are not covered.

To install the tumble dryer, follow the steps below:

1. Remove the outer wrapping and the polystyrene base. (Check for any cosmetic damage at this time.

2. Move the machine into place.

3. Adjust the levelling legs by lifting the front of the dryer slightly and adjusting the feet to the correct height.

Be careful not to screw the feet down too far and do not use a screwdriver.

NOTE:   A badly leveled machine may result in damage to the bearings and premature wear, so we

      recommend that you use a spirit level.

4. Connect the condensation hose to a drain (optional).

CONNECTING THE CONDENSATION DRAIN HOSE

Your condenser dryer has a tank that collects the condensed water. If you prefer, however, you can install
the dryer to drain the water directly to a drain pipe. To do this, follow the steps below:

1. Unplug the dryer from the electrical outlet.

2. Remove the vent on the back of the machine (Fig 1).

3. Remove the clamp and carefully remove the hose (Fig 2).

4. Position the hose on the free inlet and reposition the clamp (Fig 3).

5. Position the hose provided on the front inlet and clamp it into place (Fig 3).

6. Remove the cover from the hole in the vent cover and insert the hose through the hole (Fig 3).

7. Replace the vent cover.

8. Insert the other end of the hose into the drain and secure into place.

Fig. 1

Fig. 2

Fig. 3

Summary of Contents for TD 800

















Reviews: