Maktec MT870 Instruction Manual Download Page 4

wiring or its own cord.

 Cutting accessory 

contacting a "live" wire may make exposed metal 
parts of the power tool "live" and could give the 
operator an electric shock. 

4. 

Wear a hard hat (safety helmet), safety glasses 
and/or face shield. Ordinary eye or sun 
glasses are NOT safety glasses. It is also 
highly recommended that you wear a dust 
mask and thickly padded gloves. 

5. 

Be sure the bit is secured in place before 
operation. 

6. 

Under normal operation, the tool is designed 
to produce vibration. The screws can come 
loose easily, causing a breakdown or accident. 
Check tightness of screws carefully before 
operation. 

7. 

In cold weather or when the tool has not been 
used for a long time, let the tool warm up for a 
while by operating it under no load. This will 
loosen up the lubrication. Without proper 
warm-up, hammering operation is difficult. 

8. 

Always be sure you have a firm footing. 
Be sure no one is below when using the tool in 
high locations. 

9. 

Hold the tool firmly with both hands. 

10. 

Keep hands away from moving parts. 

11. 

Do not leave the tool running. Operate the tool 
only when hand-held. 

12. 

Do not point the tool at any one in the area 
when operating. The bit could fly out and 
injure someone seriously. 

13. 

Do not touch the bit or parts close to the bit 
immediately after operation; they may be 
extremely hot and could burn your skin. 

14. 

Some material contains chemicals which may 
be toxic. Take caution to prevent dust 
inhalation and skin contact. Follow material 
supplier safety data. 

SAVE THESE INSTRUCTIONS. 

 

WARNING: 

DO NOT let comfort or familiarity with product 
(gained from repeated use) replace strict adherence 
to safety rules for the subject product. MISUSE or 
failure to follow the safety rules stated in this 
instruction manual may cause serious personal 
injury. 

 
 
 

FUNCTIONAL DESCRIPTION 

 

CAUTION: 

• 

Always be sure that the tool is switched off and 
unplugged before adjusting or checking function on 
the tool. 

Switch action 

1

2

 

 

012279 

CAUTION: 

• 

Before plugging in the tool, always check to see 
that the switch trigger actuates properly and returns 
to the "OFF" position when released. 

• 

Switch can be locked in "ON" position for ease of 
operator comfort during extended use. Apply 
caution when locking tool in "ON" position and 
maintain firm grasp on tool. 

To start the tool, simply pull the switch trigger. Tool speed 
is increased by increasing pressure on the switch trigger. 
Release the switch trigger to stop. For continuous 
operation, pull the switch trigger, push in the lock button 
and then release the switch trigger. To stop the tool from 
the locked position, pull the switch trigger fully, then 
release it. 

Reversing switch action 

A

B

1

 

 

012280 

CAUTION: 

• 

Always check the direction of rotation before 
operation. 

• 

Use the reversing switch only after the tool comes 
to a complete stop. Changing the direction of 
rotation before the tool stops may damage the tool. 

• 

If the switch trigger can not be depressed, check to 
see that the reversing switch is fully set to 
position

 (A side) or

(B side). 

1. Reversing 

switch lever 

1. Switch trigger 
2. Lock button 

Summary of Contents for MT870









Reviews: