Maktec MT560 Instruction Manual Download Page 3

electric shock. 

9. 

If operating a power tool in a damp location is 
unavoidable,  use  a  residual  current  device 
(RCD) protected supply.

 Use of an RCD reduces 

the risk of electric shock.   

10. 

Use  of  power  supply  via  a  RCD  with  a  rated 
residual  current  of  30mA  or  less  is  always 
recommended. 

Personal safety 

11. 

Stay alert, watch what you are doing and use 
common  sense when  operating  a  power  tool. 
Do not use a power tool while you are tired or 
under  the  influence  of  drugs,  alcohol  or 
medication.

  A  moment  of  inattention  while 

operating  power  tools  may  result  in  serious 
personal injury. 

12. 

Use  personal  protective  equipment.  Always 
wear eye protection.

 Protective equipment such 

as dust mask, non-skid safety shoes, hard hat, or 
hearing protection used for appropriate conditions 
will reduce personal injuries.   

13. 

Prevent  unintentional  starting.  Ensure  the 
switch is in the off-position before connecting 
to  power  source  and/or  battery  pack,  picking 
up or carrying the tool.

 Carrying power tools with 

your finger on the switch or energising power tools 
that have the switch on invites accidents.   

14. 

Remove  any  adjusting  key  or  wrench  before 
turning the power tool on.

 A wrench or a key left 

attached to a rotating part of the power tool may 
result in personal injury. 

15. 

Do  not  overreach.  Keep  proper  footing  and 
balance at all times.

 This enables better control 

of the power tool in unexpected situations. 

16. 

Dress properly. Do not wear loose clothing or 
jewellery. Keep your hair, clothing, and gloves 
away  from  moving  parts.

  Loose  clothes, 

jewellery  or  long  hair  can  be  caught  in  moving 
parts. 

17. 

If  devices  are  provided  for  the  connection  of 
dust  extraction  and  collection  facilities, 
ensure these are connected and properly used.

 

Use  of  dust  collection  can  reduce  dust-related 
hazards. 

Power tool use and care 

18. 

Do  not  force  the  power  tool.  Use  the  correct 
power  tool  for  your  application.

  The  correct 

power tool will do the job better and safer at the 
rate for which it was designed. 

19. 

Do  not  use  the  power  tool  if  the  switch  does 
not turn it on and off.

 Any power tool that cannot 

be  controlled  with  the  switch  is  dangerous  and 
must be repaired. 

20. 

Disconnect  the  plug  from  the  power  source 
and/or  the  battery  pack  from  the  power  tool 

before  making  any  adjustments,  changing 
accessories,  or  storing  power  tools.

  Such 

preventive  safety  measures  reduce  the  risk  of 
starting the power tool accidentally. 

21. 

Store  idle  power  tools  out  of  the  reach  of 
children  and  do  not  allow  persons  unfamiliar 
with  the  power  tool  or  these  instructions  to 
operate  the  power  tool.

  Power  tools  are 

dangerous in the hands of untrained users. 

22. 

Maintain power tools. Check for misalignment 
or binding of moving parts, breakage of parts 
and  any  other  condition  that  may  affect  the 
power  tool’s  operation.  If  damaged,  have  the 
power tool repaired before use.

 Many accidents 

are caused by poorly maintained power tools. 

23. 

Keep  cutting  tools  sharp  and  clean.

  Properly 

maintained cutting tools with sharp cutting edges 
are less likely to bind and are easier to control. 

24. 

Use the power tool, accessories and tool bits 
etc.  in  accordance  with  these  instructions, 
taking  into  account  the  working  conditions 
and the work to be performed.

 Use of the power 

tool  for  operations  different  from  those  intended 
could result in a hazardous situation. 

Service 

25. 

Have  your  power  tool  serviced  by  a  qualified 
repair person using only identical replacement 
parts.

 This will ensure that the safety of the power 

tool is maintained. 

26. 

Follow  instruction  for  lubricating  and 
changing accessories. 

27. 

Keep handles dry, clean and free from oil and 
grease. 

GEB029-3 

CIRCULAR SAW SAFETY 
WARNINGS 

1. 

DANGER:

 

Keep  hands  away  from  cutting  area  and  the 
blade.  Keep  your  second  hand  on  auxiliary 
handle,  or  motor  housing.

  If  both  hands  are 

holding the saw, they cannot be cut by the blade. 

2. 

Do  not  reach  underneath  the  workpiece.

  The 

guard cannot protect you from the blade below the 
workpiece. Do not attempt to remove cut material 
when blade is moving. 
CAUTION:  Blades  coast  after  turn  off.  Wait  until 
blade stops before grasping cut material. 

3. 

Adjust  the  cutting  depth  to  the  thickness  of 
the workpiece.

 Less than a full tooth of the blade 

teeth should be visible below the workpiece. 

4. 

Never  hold  piece  being  cut  in  your  hands  or 
across  your  leg.  Secure  the  workpiece  to  a 
stable platform.

 It is important to support the work 

properly to minimize body exposure, blade binding, 

Summary of Contents for MT560













Reviews: