12 ENGLISH
Hold the blower upright by grabbing the handle of the
blower. Place the outlet of the blower on the gutter and
then turn on the blower.
►
Fig.23
For UX01G users
NOTICE:
When using the gutter nozzle set, if you
use UX01G as the power unit and install BL4080F
to UX01G, do not use the shoulder harness
included in the power unit package, but use the
recommended shoulder harness shown below.
For the recommended shoulder harness, ask Makita
Authorized Service Centers.
Attaching the shoulder harness
CAUTION:
Always use the shoulder harness
attached to the power unit. Before operation,
adjust the shoulder harness according to the user
size to prevent fatigue.
CAUTION:
Before operation, make sure that
the shoulder harness is properly attached to the
hanger on the power unit.
CAUTION:
Before operation, make sure that
the buckle of the shoulder harness is fastened
firmly.
CAUTION:
Always use the shoulder har-
ness shown below. Do not use other shoulder
harnesses.
1.
Put on the shoulder harness and fasten the
buckle.
►
Fig.24:
1.
Buckle
NOTE:
When removing the shoulder harness, unlock
the buckle and remove the shoulder harness.
2.
Adjust the shoulder harness to a comfortable
working position.
►
Fig.25
3.
Clasp the hook on the shoulder harness to the
hanger of the power unit.
►
Fig.26:
1.
Hook
2.
Hanger
The shoulder harness features a means of quick
release. Simply squeeze the sides of the buckle to
release the shoulder harness.
►
Fig.27:
1.
Buckle
MAINTENANCE
WARNING:
Before inspecting or maintaining
the equipment, switch off the motor and remove
the battery cartridge.
Otherwise, the fans may move
and result in serious injury.
WARNING:
When inspecting or maintaining
the equipment, always put it down.
Assembling or
adjusting the equipment in an upright position may
result in serious injury.
WARNING:
Follow the warnings and precau-
tions in the chapter “SAFETY WARNINGS” and
the instruction manual of the power unit.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
Cleaning the machine
Clean the machine by wiping off dust with a dry cloth or
one dipped in soapy water and wrung out.
►
Fig.28
Remove dust or dirt from the suction inlet at the rear of
the attachment.
►
Fig.29:
1.
Suction inlet
Overall inspection
Check for damaged parts. Ask our authorized service
center to replace them if necessary.
Lubricating moving parts
NOTICE:
Follow the instruction of the frequency
and amount of grease supplied.
Otherwise insuffi
-
cient lubrication may damage moving parts.
Drive axle:
Apply grease (Makita grease N No.2 or equivalent)
every 30 hours of operation.
►
Fig.30
NOTE:
Genuine Makita grease may be purchased
from your local Makita dealer.
Storage
When storing the attachment separated from the power
unit, put the cap onto the end of the pipe.
►
Fig.31
Summary of Contents for UB402MP
