background image

2

SPECIFICATIONS

• Manufacturer reserves the right to change specifications without notice.

• Specifications may differ from country to country.

GENERAL SAFETY RULES

USA002-2

(For All Tools)

WARNING:

Read and understand all instructions.

 Failure to follow all

instructions listed below, may result in electric shock, fire and/or
serious personal injury.

SAVE THESE INSTRUCTIONS

Work Area

1.

Keep your work area clean and well lit.

Cluttered benches and dark areas invite acci-
dents.

2.

Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases, or dust.

 Power

tools create sparks which may ignite the dust
or fumes.

3.

Keep bystanders, children, and visitors
away while operating a power tool.

 Distrac-

tions can cause you to lose control.

Electrical Safety

4.

Double insulated tools are equipped with
a polarized plug (one blade is wider than
the other.) This plug will fit in a polarized
outlet only one way. If the plug does not fit
fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified elec-

Model

NHP1030

Capacities

Concrete

10 mm (3/8”)

Steel

10 mm (3/8”)

Wood

18 mm (3/4”)

No load speed (RPM)

0 - 2,700/min.

Blows per minute

0 - 29,700

Overall length

270 mm (10-5/8”)

Net weight

1.6 kg (3.5 lbs)

Summary of Contents for NHP1030

















Reviews: