![background image](http://html.mh-extra.com/html/makita/m9800-series/m9800-series_instruction-manual_1722846007.webp)
7 ENGLISH
The sanding pad has a hook and loop type fitting sys
-
tem which allows easy and rapid fitting of a sanding
paper.
A s sand ing papers h av e h oles f or d ust ex trac tion,
mount a sand ing paper so th at th e h oles in a sand ing
paper matc h th ose in th e sand ing pad .
T o remov e a sand ing paper, raise its end and peel it of f .
Loosen and remove the application tool installation bolt
using a h ex w renc h and th en take of f th e applic ation
tool.
►
Fig.3:
1.
Application tool installation bolt
2.
H oles
in th e applic ation tool
3.
P rotrusions of th e
tool flange
►
Fig.4:
1.
Application tool installation bolt
2.
H ex
w renc h
3.
T igh ten
W h en using applic ation tools w ith a d if f erent ty pe of
installation sec tion, use a c orrec t ad apter ( optional
ac c essory ) .
►
Fig.5:
1.
Application tool installation bolt
2.
H oles in
th e applic ation tool
3.
A d apter
4.
P rotrusions
of the tool flange
OPERATION
WARNING:
Before starting the tool and
during operation, keep your hand and face aw ay
from the application tool.
CAUTION:
Do not apply excessive load to the
tool w hich may cause a motor lock and stop the
tool.
Cutting, saw ing and scraping
CAUTION:
Do not move on the tool forcibly
in the direction ( eg. tow ards either side) of tool
application w ith no cutting edge.
I t may d amage
th e tool.
P ut th e applic ation tool on th e w orkpiec e.
A nd th en mov e th e tool f orw ard so th at th e applic ation
tool mov ement d oes not slow d ow n.
►
Fig.6
NOTE:
F orc ing or ex c essiv e pressure on th e tool may
reduce efficiency.
NOTE:
Bef ore c utting operation, it is rec ommend ed to
preset the orbital stroke rate 3 - 5.
Sanding
CAUTION:
Do not reuse a sanding paper used
for sanding metal to sand w ood.
CAUTION:
Do not use a w orn sanding paper
or sanding paper w ithout grit.
A pply a sand ing paper on th e w orkpiec e.
►
Fig.7
NOTE:
U sing a test material sample to try is rec om-
mendable to determine a correct orbital stroke rate
suitable for your work.
NOTE:
U se a sand ing paper w ith th e same grit until
sand ing th e w h ole w orkpiec e is c ompleted . R eplac ing
a sand ing paper w ith d if f erent grit sand ing paper may
not get a fine finish.
Dust extraction attachment
Optional accessory
WARNING:
Do not use extraction attachment
w hen grinding a metallic w orkpiece w ith this tool.
H ot d ust may ignite d ust in th e v ac uum c leaner and it
may cause fire.
W h en y ou w ish to perf orm c leaner operation, install th e
dust extraction attachment to the tool. Connect a hose
of v ac uum c leaner to th e d ust ex trac tion attac h ment.
►
Fig.8
Assemble the dust extraction attachment and install it
to th e tool.
1.
Install joint, dust nozzle and dust attachment.
2.
Install the nozzle band on the tool so that its pro
-
trusions fit in the holes in the tool to secure it.
3.
P ut th e f elt ring, spac er ( if nec essary ) , and th e
sand ing pad on th e d ust attac h ment and th en sec ure
them with the application tool installation bolt.
►
Fig.9:
1.
Joint
2.
Nozzle band
3.
Dust nozzle
4.
D ust attac h ment
5.
S pac er
6.
F elt ring ( ø
4 7 mm)
7.
Pad (with STARLOCK marking)
8.
Application tool installation bolt
9.
F elt ring
( ø 37 mm)
10.
P ad ( w ith O I S marking)
NOTICE:
When using the pad with STARLOCK
marking, be sure to install the spacer between the
d ust attac h ment and th e f elt ring.
MAINTENANCE
CAUTION:
Alw ays be sure that the tool is
sw itched off and unplugged before attempting to
perform inspection or maintenance.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
T o maintain prod uc t S A F ET Y and R EL I A BI L I T Y ,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
Cleaning
F rom time to time w ipe of f th e tool using a d ry c loth or a
c loth d ampened in soapy w ater.
►
Fig.10