![background image](http://html.mh-extra.com/html/makita/hr3000c/hr3000c_instruction-manual_231157007.webp)
ENGLISH
Explanation of general view
1
Bit grease
2
Bit shank
3
Bit
4
Chuck cover
5
Change lever
6
Shift lever
7
‘‘Rotation
with
hammering’’
symbol
8
Lock button
9
Pointer
0
‘‘Hammering only’’ symbol
q
‘‘Rotation only’’ symbol
w
Loosen
e
Tighten
r
Side grip
t
Switch trigger
y
Adjusting dial
u
Clamp screw
i
Depth gauge
o
Power-ON indicator lamp
(green)
p
Service indicator lamp (red)
a
Screwdriver
s
Brush holder cover
d
Brush holder cap
f
Screws
g
Connector
h
Black
j
White
k
Crank cap
l
Hex wrench
;
Hammer grease
z
Drill chuck
SPECIFICATIONS
Model
HR3000C
Capacities
Tungsten-carbide tipped bit ........................ 30 mm
Core bit ....................................................... 90 mm
Wood .......................................................... 30 mm
Steel ........................................................... 13 mm
No load speed (min
-1
) ............................... 360 – 720
Blows per minute ................................ 1,650 – 3,300
Overall length ............................................... 391 mm
Net weight ....................................................... 4.8 kg
• Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
• Note: Specifications may differ from country to
country.
Power supply
The machine should be connected only to a power
supply of the same voltage as indicated on the
nameplate, and can only be operated on single-phase
AC supply. They are double-insulated in accordance
with European Standard and can, therefore, also be
used from sockets without earth wire.
Safety hints
For your own safety, please refer to enclosed the
safety instructions.
ADDITIONAL SAFETY RULES
1. Wear a hard hat (safety helmet), safety glasses
and/or face shield. It is also highly recom-
mended that you wear a dust mask, ear pro-
tectors and thickly padded gloves.
2. Be sure the bit is secured in place before
operation.
3. Under normal operation, the machine is
designed to produce vibration. The screws
can come loose easily, causing a breakdown
or accident. Check tightness of screws care-
fully before operation.
4. In cold weather or when the machine has not
been used for a long time, let the machine
warm up for several minutes by operating it
under no load. This will loosen up the lubrica-
tion. Without proper warm-up, hammering
operation is difficult.
5. Always be sure you have a firm footing. Be
sure no one is below when using the machine
in high locations.
6. Hold the machine firmly with both hands.
7. Keep hands away from moving parts.
8. Do not leave the machine running. Operate the
machine only when hand-held.
9. Do not point the machine at any one in the
area when operating. The bit could fly out and
injure someone seriously.
10. When drilling or chipping into walls, floors or
wherever
‘‘live’’ electrical
wires
may
be
encountered, DO NOT TOUCH ANY METAL
PARTS OF THE MACHINE! Hold the machine
by the insulated grasping surfaces to prevent
electric shock if you drill or chip into a ‘‘live’’
wire.
11. Do not touch the bit or parts close to the bit
immediately after operation; they may be
extremely hot and could burn your skin.
SAVE THESE INSTRUCTIONS.
HR3000C (E) (’99. 5. 19)
7
Summary of Contents for HR3000C
