manualshive.com logo in svg

Makita HM0871C, Technical Information

Share
Download
Makita HM0871C Technical Information Download Page 14

P 1

4

/ 1

7

Fig. 34

[3]-9 Handle section

(1) Disassemble Handle section as per the left illustration in 

Fig. 29

.

(2) Remove Handle cover by unscrewing 4x18 Tapping screw to replace the electrical parts in Handle.  See 

Fig. 34

. 

Power supply cord

Remove 4x18 Tapping screw and Handle cover.
Switch and Power supply cord can be replaced.
Rubber pin 4 comes out after removing Switch.

4x18 Tapping 
screw

Switch

Rubber pin 4

Handle cover

R

epair

ASSEMBLING

Fig. 35

Fig. 36

Unscrew 5x25 Tapping screws. So Vibration absorbing handle can be disassembled in five parts as illustrated below. 

(3) In case of HM0871C, the Vibration absorbing handle section can be disassembled as illustrated in 

Fig. 35

.

Assemble Handle section as illustrated in 

Fig. 36

.

Dust Cover 
Support

Dust cover support

Assemble Dust cover support to Handle base, facing its Triangle mark to Back side.  
When assembling Dust cover to Dust cover support, face the >NBS< mark to
 Triangle mark on Dust cover support. 

Dust cover 

Dust cover 

Handle

Handle
cover

5x25 Tapping
screw (2pcs.)

Flat washer 5 (2pcs.)

Handle base

Compression
spring 11

“>NBS<” Mark

Triangle mark

Back side

Summary of Contents for HM0871C


















Reviews:

No comments

Brands by name

Popular brands

Load more brands