background image

15

5)   Set  the  engine  level,  and  gradually  fill  up  to  upper  limit  mark  with  new  oil.

6)   After  filling,  tightly  secure  oil  cap,  so  that  it  will  not  loosen  and  cause  leaks.

 

If oil cap is not tightly secured, it may leak.

Upper limit mark

Oil

Internal stepped 

section (upper 

limit)

External mark 

(lower limit)

Internal stepped 

section (lower 

limit)

External mark 

(upper limit)

CLEANING OF AIR CLEANER

WARNING:

Shut  off  the  engine,  keep  away  from  open  flames  

and do not smoke.

Interval of Cleaning and Inspection: Daily (every 10 operating hours)

Turn the choke lever to the full close side, and keep the carburetor off from 

 

dust or dirt.

Loosen  the  fixing  bolt.

 

Remove the air cleaner cover by pulling its bottom side.

 

Remove the elements and tap them to remove dirt.

 

If the elements are heavily contaminated: 

 

 Remove the elements, immerse them in warm water or in water-diluted 

neutral detergent, and dry them completely. Do not squeeze or rub them 

when washing.

Before  attaching  the  elements,  be  sure  to  dry  them  completely.  Insufficient  

 

drying  of  the  elements  may  lead  to  difficult  startup.

Wipe out oil adhering around the air cleaner cover and the breather part with 

 

waste cloth.
Fit the element (sponge) into the element (felt). 

 

Fit the elements into the plate so that the sponge faces the air cleaner cover.

Immediately  attach  the  cleaner  cover  and  tighten  it  with  fixing  bolts.  (In  

 

remounting,  first  place  the  upper  claw,  and  then  the  lower  claw.)

NOTICE:

Clean the elements several times a day, if excessive dust adheres to it. 

 

Dirty  elements  reduce  engine  power  and  make  starting  engine  difficult.

Remove oil on the elements. If operation continues with the elements 

 

remaining not cleared of oil, oil in the air cleaner may fall outside, resulting 
in contamination of the environment.
Do not put the elements on the ground or dirty place. Otherwise they pick 

 

up dirt or debris and it may damage the engine.
Never use fuel for cleaning the elements. Fuel may damage them.

 

Plate

Element (sponge)

Air cleaner 

cover

Fixing bolt

Element (felt)

Breather Part

Choke 

lever

POINTS ON OIL

Never discard replaced engine oil in garbage, earth or sewage ditch. Disposal of oil is regulated by law. In disposal, always follow the 

 

relevant laws and regulations. For any points remaining unknown, contact Authorized Service Agent.
Oil will deteriorate even when it is kept unused. Perform inspection and replacement at regular intervals (replace with new oil every 

 

6 months).

Summary of Contents for ER2650LH





















Reviews: