background image

 

Separating/Connecting Engine and Tool 

1.

 

Separation 

Loosen the 2 bolts on holder case in order to remove drive 
shaft from holder case(Fig .II-1). 

2.

 

Connection 

 

1.Fully insert the drive shaft into the holder case               

(Approximately 60 mm;2-3/8",). If the inner shaft resists  full 
insertion of the drive shaft, insert it again  after slightly 
rotating the drive shaft or the  support washer on the gear case 
to match the  inner shaft with the hole inside the holder case. 

 

2.After making sure that the drive shafts is installed fully and 

correctly, tighten the screws  M5 X 18 to secure the drive 
shaft. 

 

Connection of throttle wire  

 

1.Connect the throttle wire (Fig .II-2)

 

2.Squeeze the throttle lever to make sure  that the throttle 
wire moves smoothly. 

 

3.Connect the switch cords to the two cords  from the 
engine by inserting one into the  other. 

 

4.Wrap the waist pad around the drive shaft so  that the 
hanger will protrude through the slit in  the waist pad and 
the throttle wire and the  cords will also be wrapped under 
the waist  pad.(Fig.II-3). 

 

 

 

Fig .II-2 

 

 

Fig .II-3 

5.Insert the bullet connectors.    (Fig. II- 4). 

Fig .II-3 

 
 
 
 
 
 
 
 

 

 

 

 

Fig .II-4 

 

Summary of Contents for EM2600L

































Reviews: