background image

19 ENGLISH

4.

  Tighten the bolt.

TROUBLESHOOTING

Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the manual, 

do not attempt to dismantle the tool. Instead, ask Makita Authorized Service Centers, always using Makita replace

-

ment parts for repairs.

State of abnormality

Probable cause (malfunction)

Remedy

Motor does not run.

Battery cartridge is not installed.

Install the battery cartridge.

Battery problem (under voltage)

Recharge the battery. If recharging is not effective, 

replace battery.

The drive system does not work 

correctly.

Ask your local authorized service center for repair.

Motor stops running after a little use.

Battery's charge level is low.

Recharge the battery. If recharging is not effective, 

replace battery.

Overheating.

Stop using of tool to allow it to cool down.

Tool does not reach maximum RPM.

Battery is installed improperly.

Install the battery cartridge as described in this 

manual.

Battery power is dropping.

Recharge the battery. If recharging is not effective, 

replace battery.

The drive system does not work 

correctly.

Ask your local authorized service center for repair.

Shear blades do not move: 

 stop the machine immediately!

Inappropriate angle of shear blades.

Make sure that the head is properly fixed in the 

operational angle.

Foreign objects are caught between the 

shear blades.

1. Use the reverse button.

2. Switch off the tool and remove the battery car

-

tridge, and then remove the foreign objects using 

tools such as pliers.

The drive system does not work 

correctly.

Ask your local authorized service center for repair.

Abnormal vibration: 

 stop the machine immediately!

Shear blades are broken, bent or worn. Replace the shear blades.

The drive system does not work 

correctly.

Ask your local authorized service center for repair.

Shear blades and motor cannot stop: 

 Remove the battery immediately!

Electric malfunction.

Remove the battery and ask your local authorized 

service center for repair.

OPTIONAL 

ACCESSORIES

CAUTION:

 

These accessories or attachments 

are recommended for use with your Makita tool 

specified in this manual.

 The use of any other 

accessories or attachments might present a risk of 

injury to persons. Only use accessory or attachment 

for its stated purpose.

If you need any assistance for more details regard

-

ing these accessories, ask your local Makita Service 

Center.

• 

Shear blade assembly

• 

Grease vessel

• 

Shoulder harness

• 

Makita genuine battery and charger

NOTE:

 Some items in the list may be included in the 

tool package as standard accessories. They may 

differ from country to country.

Summary of Contents for DUN500WRTE





















Reviews: