![background image](http://html1.mh-extra.com/html/makita/dua300pt2/dua300pt2_instruction-manual_3966278018.webp)
18 ENGLISH
Cleaning the guide bar
Chips and sawdust will build up in the guide bar groove. They may
clog the bar groove and impair the oil flow. Clean out the chips and
sawdust every time when you sharpen or replace the saw chain.
►
Fig.37
Cleaning the sprocket cover
Chips and saw dust will accumulate inside of the
sprocket cover. Remove the sprocket cover and saw
chain from the tool then clean the chips and saw dust.
►
Fig.38
Cleaning the oil discharge hole
Small dust or particles may be built up in the oil discharge
hole during operation. These dust or particles may impair the
oil to flow and cause an insufficient lubrication on the whole
saw chain. When a poor chain oil delivery occurs at the top
of guide bar, clean the oil discharge hole as follows.
1.
Remove the sprocket cover and saw chain from the tool.
2.
Remove the small dust or particles using a slotted
screwdriver or the like.
►
Fig.39:
1.
Slotted screwdriver
2.
Oil discharge hole
3.
Insert the battery cartridge into the tool. Pull the
switch trigger to flow built-up dust or particles off the oil
discharge hole by discharging chain oil.
4.
Remove the battery cartridge from the tool.
Reinstall the sprocket cover and saw chain on the tool.
Replacing the sprocket
CAUTION:
A worn sprocket will damage a
new saw chain. Have the sprocket replaced in this
case.
Before fitting a new saw chain, check the condition of
the sprocket. If the sprocket is worn or damaged, ask
Makita Authorized Service Centers for replacement.
►
Fig.40:
1.
Sprocket
2.
Areas to be worn out
Storing the tool
1.
Clean the tool before storing. Remove any chips
and sawdust from the tool after removing the sprocket
cover.
2.
After cleaning the tool, run it under no load to lubri-
cate the saw chain and guide bar.
3.
Cover the guide bar with the guide bar cover.
4.
Empty the oil tank.
Instructions for periodic maintenance
To ensure long life, prevent damage and ensure the full functioning of the safety features, the following maintenance must
be performed regularly. Warranty claims can be recognized only if this work is performed regularly and properly. Failure to
perform the prescribed maintenance work can lead to accidents! The user of the tool must not perform maintenance work
which is not described in the instruction manual. All such work must be carried out by our authorized service center.
Check item / Operating time
Before operation
Everyday
Every week
Every 3 month
Annually
Before storage
Entire tool
Inspection.
-
-
-
-
-
Cleaning.
-
-
-
-
-
Check at
authorized
service center.
-
-
-
-
Saw chain
Inspection.
-
-
-
-
-
Sharpening if
necessary.
-
-
-
-
-
Guide bar
Inspection.
-
-
-
-
Remove from
the tool.
-
-
-
-
-
Chain
lubrication
Check the oil
feed rate.
-
-
-
-
-
Switch trigger
Inspection.
-
-
-
-
-
Lock-off lever
Inspection.
-
-
-
-
-
Oil tank cap
Check
tightness.
-
-
-
-
-
Screws and
nuts
Inspection.
-
-
-
-
-
Summary of Contents for DUA300PT2
