Makita DTD137, Instructions Manual

Page: 9 / 84

9
200
( 2 , 0 4 0 )
1 8 0
( 1 ,836)
1 6 0
( 1 ,63 2 )
1 4 0
( 1 ,4 2 8)
120
( 1 , 22 4)
100
( 1 , 020 )
8 0
(8 1 6)
6 0
(6 12 )
4 0
(4 0 8)
20
( 20 4)
0 1 . 0 2 . 0 3. 0
M 1 4
M 12
M 1 4
M 12
M 10
M8
M 10
M8
Hi gh tens il e bo l t
N m
F
asten
i
ng
tor
q
ue
F asten i ng t i me (S)
P
roper
fasten
i
ng
tor
q
ue
( kgf cm )
014971
Model DTD148
1 4 0
( 1 ,4 2 8)
120
100
8 0
6 0
4 0
20
0 1 . 0 2 . 0
M 1 4
M 12
M 10
M8
M 1 6
M 1 4
M 12
M 10
M8
S tandard bo l t
N m
F
asten
i
ng
tor
q
ue
F asten i ng t i me (S)
P
roper
fasten
i
ng
tor
q
ue
( kgf cm )
( 1 , 22 4)
( 1 , 020 )
(8 1 6)
(6 12 )
(4 0 8)
( 20 4)
M 1 6
014972
200
( 2 , 0 4 0 )
1 8 0
( 1 ,836)
1 6 0
( 1 ,63 2 )
1 4 0
( 1 ,4 2 8)
120
( 1 , 22 4)
100
( 1 , 020 )
8 0
(8 1 6)
6 0
(6 12 )
4 0
(4 0 8)
20
( 20 4)
0 1 . 0 2 . 0 3. 0
M 1 4
M 12
M 1 4
M 12
M 10
M8
M 10
M8
Hi gh tens il e bo l t
N m
F
asten
i
ng
tor
q
ue
F asten i ng t i me (S)
P
roper
fasten
i
ng
tor
q
ue
( kgf cm )
014973
Hold the tool firmly and place the point of the driver bit
in the screw head. Apply forward pressure to the tool to
the extent that the bit will not slip off the screw and turn
the tool on to start operation.
NOTE:
•
Use the proper bit for the head of the screw/bolt
that you wish to use.
•
When fastening M8 or smaller screw, choose a
proper impact force and carefully adjust pressure
on the switch trigger so that the screw is not
damaged.
•
Hold the tool pointed straight at the screw.
•
If the impact force is too strong you tighten the
screw for a time longer than shown in the figures,
the screw or the point of the driver bit may be
overstressed, stripped, damaged, etc. Before
starting your job, always perform a test operation
to determine the proper fastening time for your
screw.
The fastening torque is affected by a wide variety of
factors including the following. After fastening, always
check the torque with a torque wrench.
1. When the battery cartridge is discharged almost
completely, voltage will drop and the fastening
torque will be reduced.
2. Driver bit or socket bit
Failure to use the correct size driver bit or socket
bit will cause a reduction in the fastening torque.
3. Bolt
•
Even though the torque coefficient and the
class of bolt are the same, the proper
fastening torque will differ according to the
diameter of bolt.
•
Even though the diameters of bolts are the
same, the proper fastening torque will differ
according to the torque coefficient, the class
of bolt and the bolt length.
4. The manner of holding the tool or the material of
driving position to be fastened will affect the
torque.
5. Operating the tool at low speed will cause a
reduction in the fastening torque.
MAINTENANCE
CAUTION:
•
Always be sure that the tool is switched off and the
battery cartridge is removed before attempting to
perform inspection or maintenance except for the
following troubleshooting related to the light.
•
Never use gasoline, benzine, thinner, alcohol or
the like. Discoloration, deformation or cracks may
result.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers,
always using Makita replacement parts.