![background image](http://html.mh-extra.com/html/makita/dpb181/dpb181_instruction-manual_18348006.webp)
6
Switch action
Fig.3
CAUTION:
•
Before installing the battery cartridge into the tool,
always check to see that the switch trigger
actuates properly and returns to the "OFF"
position when released.
To prevent the switch trigger from accidentally pulled,
the trigger-lock button is provided.
To start the tool, press the trigger-lock button from B
side and pull the switch trigger.
Release the switch trigger to stop. After use, always
press in the trigger-lock button from A side.
Lighting up the lamp
CAUTION:
•
Do not look in the light or see the source of light
directly.
Fig.4
Pull the switch trigger to light up the lamp. The lamp
keeps on lighting while the switch trigger is being pulled.
The lamp goes out just after releasing the trigger.
NOTICE:
•
Do not apply impact to the lamp, which may cause
damage or shorted service time to it.
•
Use a dry cloth to wipe the dirt off the lens of lamp.
Be careful not to scratch the lens of lamp, or it
may lower the illumination.
•
Do not use thinner or gasoline to clean the lamp.
Such solvents may damage it.
ASSEMBLY
CAUTION:
•
Always be sure that the tool is switched off and the
battery cartridge is removed before carrying out
any work on the tool.
Installing or removing the blade
CAUTION:
•
Oil on the blade can cause the blade to slip or
come off unexpectedly. Wipe off all excess oil with
a cloth before installing the blade.
•
Always wear protective gloves when handling the
blade.
•
Use caution when handling the blade to avoid cut
by the sharp edge of the blade teeth.
•
Keep your body away from the blade area when
checking the blade movement.
•
When turning the blade tightening lever clockwise
to release the tension on the blade, point the tool
downward because the blade may come off
unexpectedly.
Fig.5
To install the blade:
1.
Turn the blade tightening lever clockwise until it
stops to loosen the wheel.
2. Match the direction of the arrows on the blade
and on the wheels.
Fig.6
Fig.7
3.
Insert the non-serrated side of the blade into the upper
holder and lower holder. Make sure the blade in both
upper and lower holder touches to the bottom bearings.
Fig.8
4. With pressing the middle part of the blade,
position the blade around one wheel. Moving the
wheel to A side makes it easier to do so.
5.
Position the blade on another wheel similarly.
6.
Position the edge of the blade on rubber tire.
7. Hold the blade in place and turn the blade-
tightening lever counterclockwise until it stops.
This places proper tension on the blade.
Make sure that the blade is correctly positioned around
the wheels.
Start and stop the tool two or three times to make sure
that the blade runs properly on the wheels.
To remove the blade, follow the installation procedure in
reverse.
Adjusting the stopper plate position
Fig.9
In the ordinary operation, protrude the stopper plate to
the A side fully.
When the stopper plate strikes against the obstacles
like a wall or the like at the finishing of a cut, loosen two
screws and slide it to the B side in the figure.
After sliding the stopper plate, secure it by tightening
two screws firmly.
Hook (Optional accessory)
Fig.10
Hook is useful for hanging the tool. Hang tool on a pipe
vice or other suitable, stable structure.
To install the hook, set the hook alongside the groove
and tighten it with two screws.
OPERATION
CAUTION:
•
Always hold front and rear handle. Never hold
the tool body or guards.
Hands may slip from
these locations and contact blade. Contact with
the blade may result in personal injury.
•
Make sure to hold the tool firmly when turning on
or off the tool or when cutting. Otherwise the tool
may fall and cause personal injury.
Fig.11
For stable cut, always keep at least two teeth in the cut.