19
ENGLISH
4.
Push the wireless activation button on the tool
briefly. The wireless activation lamp will blink in blue.
Fig.36:
1.
Wireless activation button
2.
Wireless
activation lamp
5.
Pull the switch trigger of the tool. Check if the
vacuum cleaner runs while the switch trigger is being
pulled.
To stop the wireless activation of the vacuum cleaner,
push the wireless activation button on the tool.
NOTE:
The wireless activation lamp on the tool will
stop blinking in blue when there is no operation for
hours. In this case, set the stand-by switch on the
vacuum cleaner to AUTO and push the wireless
activation button on the tool again.
NOTE:
The vacuum cleaner starts/stops with a delay.
There is a time lag when the vacuum cleaner detects
a switch operation of the tool.
NOTE:
The transmission distance of the wireless unit
may vary depending on the location and surrounding
circumstances.
NOTE:
When two or more tools are registered to one
vacuum cleaner, the vacuum cleaner may start run
-
ning even if you don t pull the switch trigger because
an other user is using the wireless activation function.
Description of the w ireless activation lamp status
Fig.37:
1.
Wireless activation lamp
The wireless activation lamp shows the status of the wireless activation function. Refer to the table below for the
meaning of the lamp status.
Status
Wireless activation lamp
Description
Color
On
Blinking
Duration
Standby
Blue
hours
The wireless activation of the vacuum cleaner is available. The
lamp will automatically turn off when no operation is performed
for hours.
When
the tool is
running.
The wireless activation of the vacuum cleaner is available and the
tool is running.
Tool
registration
Green
2 0 seconds
Ready for the tool registration. Waiting for the registration by the
vacuum cleaner.
2 seconds
The tool registration has been finished. The wireless activation
lamp will start blinking in blue.
Cancelling
tool
registration
Red
2 0 seconds
Ready for the cancellation of the tool registration. Waiting for the
cancellation by the vacuum cleaner.
2 seconds
The cancellation of the tool registration has been finished. The
wireless activation lamp will start blinking in blue.
Others
Red
3 seconds
The power is supplied to the wireless unit and the wireless activa
-
tion function is starting up.
Off
-
-
The wireless activation of the vacuum cleaner is stopped.
Cancelling tool registration for the
vacuum cleaner
Perform the following procedure when cancelling the
tool registration for the vacuum cleaner.
1.
Install the batteries to the vacuum cleaner and the tool.
2.
Set the stand-by switch on the vacuum cleaner to AUTO .
Fig.38 :
1.
Stand-by switch
3.
Press the wireless activation button on the vac
-
uum cleaner for seconds. The wireless activation
lamp blinks in green and then become red. After that,
press the wireless activation button on the tool in the
same way.
Fig.39:
1.
Wireless activation button
2.
Wireless
activation lamp
If the cancellation is performed successfully, the wire
-
less activation lamps will light up in red for seconds
and start blinking in blue.
NOTE:
The wireless activation lamps finish blinking in
red after seconds elapsed. Press the wireless acti
-
vation button on the tool while the wireless activation
lamp on the cleaner is blinking. If the wireless acti
-
vation lamp does not blink in red, push the wireless
activation button briefly and hold it down again.
Summary of Contents for DGA701
