11 ENGLISH
For model DFJ212 / DFJ213 / DFJ214 / DFV210
►
Fig.12:
1.
Power cable
2.
Hole
3.
Cable holder
7.
(For DFJ212 / DFJ213 / DFJ214 / DFV210 only)
Close the zip fastener after installing or removing the
fan unit.
8.
Connect the other end of the power cable to the
battery holder.
►
Fig.13:
1.
Battery holder
CAUTION:
Always use the strip and snap
button to secure the fan unit to the jacket.
If the
fan unit falls, it may cause an injury, or damage to the
fan unit.
Follow the installation procedure in reverse when
removing it.
Attaching the filter set
Optional accessory
The filter set protects the fan unit from dust and powder.
We recommend that you use the filter set in a dusty or
powdery work place.
Insert the filter attachment between the jacket and fan
unit as shown in the figure.
►
Fig.14:
1.
Ring
2.
Hole in the jacket
3.
Filter attach-
ment
4.
Fan unit
5.
Filter
When tightening the ring, stop it at the mark near the
slot on the fan unit. After attaching the fan units, cover
the filter attachments with filters.
►
Fig.15:
1.
Mark
2.
Slot
NOTICE:
Make sure that the filter fully covers
the filter attachment. For better protection against
dust and powder, tuck the skirt of the filter
between the jacket and filter attachment.
FUNCTIONAL
DESCRIPTION
NOTICE:
The fan jacket is effective when the
humidity and temperature of intake air are lower
than those of the body surface. The fan jacket
may not be effective if the air temperature and/or
humidity are higher than those inside the jacket.
Power button
To turn on the jacket, press and hold the power button
on the battery holder (optional accessory). The jacket
starts at high air speed. Each time you tap the power
button, the air speed changes from high to medium,
medium to low, and low to high. The air speed indicator
shows the current air speed.
►
Fig.16:
1.
Air speed indicator
2.
Power button
To turn off, press and hold the power button again.
Indicating the remaining battery capacity
Only for battery cartridges with the indicator
►
Fig.17:
1.
Indicator lamps
2.
Check button
Press the check button on the battery cartridge to indi-
cate the remaining battery capacity. The indicator lamps
light up for a few seconds.
Indicator lamps
Remaining
capacity
Lighted
Off
Blinking
75% to 100%
50% to 75%
25% to 50%
0% to 25%
(For 14.4 V and 18 V batteries only)
Charge the
battery.
(For 14.4 V and 18 V batteries only)
The battery
may have
malfunctioned.
NOTE:
Depending on the conditions of use and the
ambient temperature, the indication may differ slightly
from the actual capacity.
Battery protection system
The device is equipped with a battery protection sys-
tem. This system automatically cuts off power to the
motor to extend battery life.
If the remaining battery capacity is too low, the device will not oper-
ate. When you turn the device on, the motor will run again, but stops
soon. In this situation, remove and recharge the battery cartridge.
Turbo button
By pressing turbo button on the battery holder, the jacket
works in turbo mode for quick cooling. Turbo mode lasts
for a minute and then air speed returns to normal.
►
Fig.18:
1.
Turbo button
Air flow
For DFJ210 / DFJ211 / DFJ310 / DFJ311 / DFJ410 /
DFJ411 only
To maintain a stable air flow, close the button at the
neck of the jacket. Fasten the button on the ribbon for
better air flow in the back.
►
Fig.19:
1.
Ribbon
Air flow inside the jacket is shown below.
►
Fig.20
For a jacket with a hood, wear the hood over a helmet. The
air from the fan goes through the helmet and cools your head.
►
Fig.21
Summary of Contents for DFJ212ZM
