Makita DCS510 Owner'S And Safety Manual Download | Manualshive

Page: 3 / 39

background image

3

RE Y

The DCS460, DCS510 will be delivered in a protective cardboard box to prevent transport damage. Cardboard is
a basic raw material and is consequently reuseable or suitable for recycling (waste paper recycling).

Contents

Page

Delivery inventory

4

Symbols

4

Safety precautions

5-16

Denomination of components

17

Technical data

18

Mounting the guide bar and saw chain

19-20

Checking the chain tension

21

Retightening the saw chain

21

Chain brake

21

Engaging the chain brake

21

Fuel / Refuelling

22-23

Chain lubrication

24

Starting the engine

25

Stopping the engine

25

Checking the chain brake

26

Working in winter

26

Adjusting the carburetor

27

Contents

Page

Sharpening the saw chain

28-29

Cleaning the brake band and sprocket interior

30

Cleaning the guide bar

30

Replacing the saw chain

31

Cleaning the air filter

32

Replacing the spark plug

33

Checking the muffler screws

33

Replacing the starter cable

34

Replacing the return spring

34

Mounting the fan housing

34

Cleaning the cylinder area

35

Replacing the fuel filter

35

Replacing / cleaning the spark arrester screen

35

Instructions for daily and periodic maintenance

36

Service, spare parts and guarantee

36-37

Troubleshooting

37

Extract from the spare parts list

38-39

This product complies with:

American National Standard Institute B 175.1-2000 chain saw safety standard.
Canadian Standards Association

Z62.1-03 chain saw safety standard.
Z62.3-04 chain saw kickback standard.

Society of Automotive Engineers

SAEJ 335-Jun 95 „Multiposition small
engine exhaust system fire ignition
suppression”

The Emissions Compliance Period referred to on the emission Compliance label indicates the number of operating
hours for which the engine has been shown to meet federal emissions requirements.
Category C= 50 hours, B= 125 hours, and A= 300 hours.

With the purchase of this chain saw you have chosen a German quality product. Important instructions for the
assembly and operation of this saw are given in this manual. For your own safety, we ask you to read the accident
prevention instructions very carefully before putting your chain saw into operation, as incorrect handling can,
despite all precautions, lead to accidents. With a little care and attention you will have good service and lasting
satisfaction from this first-rate product.

DCS460, DCS510

WARNING !

Careless or improper use of this product can cause serious or even fatal injury.
Before operating a chain saw or other MAKITA products it is important that you read, fully understand and

carefully follow the instructions outlined in this owners manual. Kickback may cause severe or fatal injury and

is one of many potential dangers in operating a chain saw. Kickback and other safety related precautions are

described in detail within this owners manual.

«
1
2
3
4
5
...
»

Summary of Contents for DCS510








































Reviews:

No comments

Related manuals for DCS510

Brand: Echo Pages: 8

Brand: Echo Pages: 64

Brand: Hyundai power products Pages: 48

Brand: Haussmann Pages: 30

Brand: MacAllister Pages: 62

Brand: Stihl Pages: 25

Brand: Ryobi Pages: 95

Brand: Poulan Pro Pages: 3

Brand: Tanaka Pages: 16

Brand: Tanaka Pages: 20

Brand: Makita Pages: 8

Brand: Makita Pages: 236

Brand: Makita Pages: 136

Brand: Makita Pages: 144

Brand: Makita Pages: 18

Brand: Metabo Pages: 128

OILOMATIC saw chain

Brand: Stihl Pages: 11

Brand: Stihl Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands