Makita BUH550 Technical Information Download Page 4

4

 9

R

epair

[3] DISASSEMBLY/ASSEMBLY

[3]-1. Shear Blade Assembly, Gear Complete (cont.)

M5x25 Pan head screws (2pcs.)

Shear blade 

assembly

Guide plate

Sleeve 5 (1pc. each) in the holes of 

Shear blade assembly

Fig. 5

(1) Assemble Flat washer 8 and Ball bearing 608ZZ to the both sides of Gear complete. And then, mount Gear complete

     to the machine. (Fig. 4)

(2) Assemble Shear blade assembly. (

Fig. 5

)

ASSEMBLING

1. Slide Guide plate on Shear blade assembly 

    to align the holes for M5x25 Pan head screws

    with Sleeves 5.

3. Align Crank section of Gear complete to 

    the elliptical hole of Shear blade assembly

    as drawn below.  And then, secure Shear 

    blade assembly by tightening M5x25 Pan  

    head screws.

4. Make sure that the two shear blades can reciprocate

    in order by turning the crank of Gear complete with

    slotted screwdriver as drawn below.

2. Pass M5x25 Pan head screws through Sleeves 5 

    in the holes of Shear blade assembly. 

M5x25 

Pan head screws 

(2pcs.)

[3]-2. Armature, Switch

Fig. 6

DISASSEMBLING

Holder cap covers

Gear housing complete

1. Remove Holder cap covers

    with Slotted screwdriver. 

    And remove Carbon brushes.

2. Separate Gear housing complete by loosening six 4x25 Tapping screws. 

    Gear housing complete is separated from Housing set.

    Armature comes with Gear housing complete.

(1) Disassemble Shear blade assembly. (

Figs. 2

3

)

(2) Disassemble Gear complete. (

Fig.4

)

(3) Remove Carbon brushes. And separate Gear housing complete. (

Fig. 6

)

4x25 Tapping screws (6pcs.)

Summary of Contents for BUH550










Reviews: