Makita BUC300 Instruction Manual Download Page 13

13 

1

2

 

 

011229 

CAUTION: 

• 

Before using battery adapter, read all instructions 
on tools using battery. 

• 

When charging a battery cartridge, first remove it 
from the battery adapter and then charge it. It is 
not allowed to charge the battery cartridge while 
using battery adapter. 

Installing or removing battery adapter 

• 

Always switch off the tool before insertion or 
removal of the battery adapter. 

• 

To remove the battery adapter, slide it from the 
tool while sliding the button on the adapter. 

• 

To install the battery adapter, align the tongue on 
the battery adapter with the groove in the housing 
and slip it into place. Insert it all the way until it 
locks in place with a little click. If you can see the 
red indicator on the upper side of the button, it is 
not locked completely. 

 

CAUTION: 

• 

Always install the battery adapter fully until the red 
indicator cannot be seen. If not, it may accidentally 
fall out of the tool, causing injury to you or 
someone around you. 

• 

Do not install the battery adapter forcibly. If the 
adapter does not slide in easily, it is not being 
inserted correctly. 

• 

The way of removing or installing a battery 
cartridge from or on the battery adapter is the 
same as that of removing or installing it from or on 
the tools. 

• 

Press down the hook securely as far as it will go 
when the battery adapter is hooked on the waist 
belt and similar objects. 

Arm cord hook (Accessory) 

 

CAUTION: 

• 

Do not attach the holder of arm cord hook to other 
than the extension cord. Failure to do so may 
cause an accident or personal injury. 

Using the arm cord hook helps to minimize a risk of 
cutting off the extension cord unexpectedly caused by 
the loose extension cord. 

1

2

3

4

 

 

011585 

Attach firmly the arm cord hook band placing around 
your arm and pass the extension cord through the 
holder. The length of the arm cord hook band is 
adjustable. 

 

NOTE: 

• 

Do not pass the extension cord through the band. 

• 

Do not force the opening of the holder. Failure to 
do so may cause deflection and damage to it. 

Spike bumper (optional accessory) 

   

014819 

To install spike bumper, perform the following steps: 

1. 

Remove the sprocket cover, saw chain and guide 
bar as described in this instruction manual. 

2. 

Fit the holes of spike bumper along with the holes 
on the chainsaw. 

3. Tighten 

them 

firmly with screws. 

 
 
 

1. Arm cord hook band 
2. Holder 
3. Extension cord (Battery adapter) 
4. Adapter (Battery adapter) 

1. Hook 
2. Belt 

Summary of Contents for BUC300

























Reviews: