background image

Fig. D-6

W

iring diagram

BTW074, BTW104

(equipped with Automatic Impact Stop System)

Rib F

LED

Boss

Rib A

Rib B

Rib D

Rib C

Connector box

Rib F

LED

Boss

Rib A

Rib B

Rib D

Rib C

Connector 

(4 pin)

Route Lead wires (blue, red and gray)

of Impact finish indicator lamp and 

the connecting Lead wire (black) 

between Rib C and Rib D.

Impact finish indicator lamp

Route Lead wires (black, red) between 

Rib A and the inner wall of Housing set (L).

Route lead wires (black, red) between

Rib A and Rib B so that they are not pinched

with Switch.

Route the bundle of Lead wires (blue, 

black, red and gray) between Rib A 

and the inner wall of Housing set (L).

Route the bundle of Lead wires (blue, 

black, red and gray) between Rib B 

and the inner wall of Housing set (L).

Route Lead wires (black, red) between Rib B

and the inner wall of Housing set (L).

Route Lead wires (black, red) between 

the following Ribs.

  * Rib of the Boss for Screw hole

  * Rib of the Connector box

Connector (6 pin) for

connecting to Switch

Connector (4 pin) for

connecting to Impact 

finish indicator lamp

Secure Lead wires of both Connectors 

(4 pin) with Lead wire holders.

Connector (6 pin) for

connecting to Switch

Wiring of Lead wires for LED   (before setting Switch)

Wiring of Lead wires for Impact finish indicator lamp  (before setting Switch)

P  1

4

/ 1

5

Summary of Contents for BTW074
















Reviews: