Makita BL1815N Technical Information Download

Page: 14 / 15

iring diagram

Housing L side

Flag connector

Flag connector with lead wires (black) has to be connected to - Terminal

so that the lead wires pass over the mark of - poles.

Flag connector with lead wires (orange) has to connected to + Terminal

so that the lead wires face the opposite side against the mark of + poles.

Flag connector

Lead wires (orange)

Lead wires (black)

Terminal

Wiring to Terminal

Wiring to DC motor

Wiring to Switch

Mark of Poles

Housing set (L) side

Red marking for distinction of + Terminal

Connect Flag connectors with Lead wires at direction described above.

Connect Flag connector with lead wire (red) to Terminal with red marking.

Flag connector

Terminal with

Red marking

Lead wire (black)

Lead wire (red)

Terminal without red marking

Connect Flag connector to Switch at direction described above.

Lead wire (orange)

Fig. D-2

Fig. D-3

Fig. D-4

P 1

/ 1

Summary of Contents for BL1815N
















Search results

Summary of Contents for BL1815N

Reviews:

Related manuals for BL1815N

Brands by name

Popular brands

Makita BL1815N, Technical Information

Search results

Summary of Contents for BL1815N

Reviews:

Related manuals for BL1815N

Brands by name

Popular brands