6
Additional safety warnings:
17.
When using depressed centre grinding wheels,
be sure to use only fiberglass-reinforced
wheels.
18.
NEVER USE Stone Cup type wheels with this
grinder.
This grinder is not designed for these
types of wheels and the use of such a product
may result in serious personal injury.
19.
Be careful not to damage the spindle, the
flange (especially the installing surface) or the
lock nut. Damage to these parts could result in
wheel breakage.
20.
Make sure the wheel is not contacting the
workpiece before the switch is turned on.
21.
Before using the tool on an actual workpiece,
let it run for a while. Watch for vibration or
wobbling that could indicate poor installation
or a poorly balanced wheel.
22.
Use the specified surface of the wheel to
perform the grinding.
23.
Watch out for flying sparks. Hold the tool so
that sparks fly away from you and other
persons or flammable materials.
24.
Do not leave the tool running. Operate the tool
only when hand-held.
25.
Do not touch the workpiece immediately after
operation; it may be extremely hot and could
burn your skin.
26.
Always be sure that the tool is switched off
and unplugged or that the battery cartridge is
removed before carrying out any work on the
tool.
27.
Observe the instructions of the manufacturer
for correct mounting and use of wheels.
Handle and store wheels with care.
28.
Do not use separate reducing bushings or
adaptors to adapt large hole abrasive wheels.
29.
Use only flanges specified for this tool.
30.
For tools intended to be fitted with threaded
hole wheel, ensure that the thread in the wheel
is long enough to accept the spindle length.
31.
Check that the workpiece is properly
supported.
32.
Pay attention that the wheel continues to
rotate after the tool is switched off.
33.
If working place is extremely hot and humid, or
badly polluted by conductive dust, use a
short-circuit breaker (30 mA) to assure
operator safety.
34.
Do not use the tool on any materials
containing asbestos.
35.
Do not use water or grinding lubricant.
36.
Ensure that ventilation openings are kept clear
when working in dusty conditions. If it should
become necessary to clear dust, first
disconnect the tool from the mains supply
( use non metallic objects ) and avoid
damaging internal parts.
37.
When use cut-off wheel, always work with the
dust collecting wheel guard required by
domestic regulation.
38.
Cutting discs must not be subjected to any
lateral pressure.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this
instruction manual may cause serious personal
injury.
ENC007-4
IMPORTANT SAFETY
INSTRUCTIONS
FOR BATTERY CARTRIDGE
1.
Before using battery cartridge, read all
instructions and cautionary markings on (1)
battery charger, (2) battery, and (3) product
using battery.
2.
Do not disassemble battery cartridge.
3.
If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4.
If electrolyte gets into your eyes, rinse them
out with clear water and seek medical
attention right away. It may result in loss of
your eyesight.
5.
Do not short the battery cartridge:
(1)
Do not touch the terminals with any
conductive material.
(2)
Avoid storing battery cartridge in a
container with other metal objects such as
nails, coins, etc.
(3)
Do not expose battery cartridge to water
or rain.
A battery short can cause a large current
flow, overheating, possible burns and
even a breakdown.
6.
Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50
ﾟ
C (122
ﾟ
F).
7.
Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a fire.
