4
ENGLISH
Explanation of general view
1
Wheel guard
2
Screw
3
Notch
4
Side grip
5
Lock nut
6
Depressed center wheel
7
Inner flange
8
Super flange
9
Outer flange 78
10 Cut-off wheel
11 Inner flange 78
12 Dust collecting wheel guard
(optional accessory)
13 Lock nut wrench
14 Shaft lock
15 Switch trigger
16 Lock lever
17 Carbon brush
18 Insulation tip
19 Commutator
20 Brush holder cap
21 Screwdriver
SAFETY INSTRUCTIONS
ENA001-2
WARNING! When using electric tools, basic
safety precautions, including the following,
should always be followed to reduce the risk of
fire, electric shock and personal injury. Read all
these instructions before operating this product
and save these instructions.
For safe operations:
1. Keep work area clean.
Cluttered areas and benches invite injuries.
2. Consider work area environment.
Do not expose power tools to rain. Do not use
power tools in damp or wet locations. Keep work
area well lit. Do not use power tools where there
is risk to cause fire or explosion.
3. Guard against electric shock.
Avoid body contact with earthed or grounded
surfaces (e.g. pipes, radiators, ranges, refrigera-
tors).
4. Keep children away.
Do not let visitors touch the tool or extension
cord. All visitors should be kept away from work
area.
5. Store idle tools.
When not in use, tools should be stored in a dry,
high or locked up place, out of reach of children.
6. Do not force the tool.
It will do the job better and safer at the rate for
which it was intended.
7. Use the right tool.
Do not force small tools or attachments to do the
job of a heavy duty tool. Do not use tools for pur-
poses not intended; for example, do not use cir-
cular saws to cut tree limbs or logs.
8. Dress properly.
Do not wear loose clothing or jewellery, they can
be caught in moving parts. Rubber gloves and
non-skid footwear are recommended when work-
ing outdoors. Wear protecting hair covering to
contain long hair.
9. Use safety glasses and hearing protection.
Also use face or dust mask if the cutting opera-
tion is dusty.
10. Connect dust extraction equipment.
If devices are provided for the connection of dust
extraction and collection facilities ensure these
are connected and properly used.
11. Do not abuse the cord.
Never carry the tool by the cord or yank it to dis-
connect it from the socket. Keep the cord away
from heat, oil and sharp edges.
12. Secure work.
Use clamps or a vice to hold the work. It is safer
than using your hand and it frees both hands to
operate the tool.
13. Do not overreach.
Keep proper footing and balance at all times.
14. Maintain tools with care.
Keep cutting tools sharp and clean for better and
safer performance. Follow instructions for lubri-
cation and changing accessories. Inspect tool
cord periodically and if damaged have it repaired
by an authorized service facility. Inspect exten-
sion cords periodically and replace, if damaged.
Keep handles dry, clean and free from oil and
grease.
15. Disconnect tools.
When not in use, before servicing and when
changing accessories such as blades, bits and
cutters.
16. Remove adjusting keys and wrenches.
Form the habit of checking to see that keys and
adjusting wrenches are removed from the tool
before turning it on.
17. Avoid unintentional starting.
Do not carry a plugged-in tool with a finger on
the switch. Ensure switch is off when plugging in.
18. Use outdoor extension leads.
When tool is used outdoors, use only extension
cords intended for outdoor use.
19. Stay alert.
Watch what you are doing. Use common sense.
Do not operate tool when you are tired.
20. Check damaged parts.
Before further use of the tool, a guard or other
part that is damaged should be carefully checked
to determine that it will operate properly and per-
form its intended function. Check for alignment of
moving parts, free running of moving parts,
breakage of parts, mounting and any other con-
ditions that may affect its operation. A guard or
other part that is damaged should be properly
repaired or replaced by an authorized service
center unless otherwise indicated in this instruc-
tion manual. Have defective switches replaced by
an authorized service facility. Do not use the tool
if the switch does not turn it on and off.
