background image

R

epair 

P 10 / 15 

[11] Disassembling armature

1. With referring to the following section, disassemble Head covers L and R,  and gear housing cover.
[4] Disassembling Head cover section in page 3 
[5] Disassembling Gear housing cover section" at page 4
2 . Remove Rear cover by unscrewing 4 x 18 Tapping screw.  And then, remove Carbon brushes. (Fig. 34)

Carbon brushes

Tapping screw 4x18

Rear cover

3. Remove Retaining ring S-8, and separate Crank complete, Balance plate and Gear complete from the shaft of Gear 
    housing as illustrated in Fig. 35.
Note: It is not necessary to remove M4x12 Hex socket head bolt, Crank complete and Gear complete from 
          Balance plate.
          Be careful not to lose Needle bearing 407.

Retaining S-8

Crank complete

Needle bearing 407

Balance plate

4. Remove four 4x30 Tapping screws, and then separate Gear housing from Motor housing. 
    Separate Armature from Gear housing by striking Gear housing with plastic hammer. (Fig. 36)

4x30 Tapping
screws

Gear housing

Armature

Motor housing

Gear complete

5. Remove Self lock with slotted screwdriver. Magnet sleeve, Wave washer 6 and Rubber ring 19 are removed from 
    Armature shaft. Fig. 37.

Self lock

Magnet sleeve (It is not used for model 4351T.)

Wave washer 6

Rubber ring 19

Ball baring 607

Insulation washer

Fig. 34

Fig. 35

Fig. 36

Fig. 37

Summary of Contents for 4351CT
















Reviews: