background image

Statement:

1) XM receiver is compatible with Frsky brand X12S, X9D, X9E, QX7 model remote control;
2) DSM2 receiver is compatible with Spektrum brand DX18, DX9, DX8, DX6 model remote control,also compatible with some JR brand

remote control which supporting DSM2 protocol, remote control with high frequency head (LNB)conversion DSM2 protocol remote
control and Walkera brand root remote control;

3) RX-2APRO receiver is compatible with Flysky brand FS-i6, FS-i10 remote control;
4) The S-FHSS receiver is suitable for the Futaba series remote control, please set communication protocol to S-FHSS before the binding;

Smartaudio Transmitter Binding Method and Steps

Transmitter Smartaudio Setting

Firmware connector TX1,turn on TBS Smartaudio(serial 0 2048 115200 57600 0 115200)(No button on the transmitter board, all the control
is switched by the remote control gesture into the adjustment interface to switch the frequency point.)

1.Frequency and power of Smartaudio protocol and OSD controlling switch transmitter
1)Firstly,Bind Frequency. Take mode2 as an example: Center back the remote control joystick in the unlocked state. Put the left joystick to
the most left, put the right joystick to the most up, enter to the OSD adjusting mode. After entering this mode,“Pitch”on remote controller
means scroll Up and down the menu.Turn the “Roll”button to the right means enter into the sub-menu, “BACK” means exits the menu.

choose “FEATURES”after entering the menu

Summary of Contents for Armor 85 HD
















Reviews: