TECHNICAL SPECIFICATIONS
Model
Lion X 650
Lion X 850
Lion X 1200
Lion X 1500
Lion X 2200
Capacity(VA/W)
650/390
850/510
1200/720
1500/900
2200/1200
Input
Voltage Range
162~290Vac
Nominal Frequency
50/60Hz
Output
On Battery Output Voltage
Simulated Sine Wave at /-10%
On Battery Output Frequency
50/60Hz +/-1%
Overload Protection
Breaker / Fuse
Physical
Dimensions (W x H x D)(mm)
96 x 138 x 286
148 X 178 X 298
Battery
Sealed Maintenance
12V 7AH x1
12V 9AH x1
12V 7AH x2
12V 9AH x2
12V 9AH x2
Free Lead Acid Battery
Typical Recharge Time
8 Hours
Warning Diagnostics
Indicators
Power On
Audible Alarms
On Battery, Low Battery, Overload, Fault
Environmental
Operating Temperature
0
℃
to 40
℃
Operating Relative Humidity
0 to 90%
Management
Auto-Charger
Yes
Auto-Restart
Yes
USB COMM. Port
Optional
RJ45/11 Communication
Protection Ports
Optional
DEFINITIONS FOR ILLUMINATED LCD INDICATORS
LCD Indication
Setting Item
Line mode
PV mode
Bat-mode
Fault/Alarm
Sound disable
Bat mode: battery capacity
Line mode:
1. Battery charging: cycle lighting
Load capacity
2. Battery full charged: lighting
3. Line mode without charger:
battery capacity
LED Indication and Alarm
LED Status (650/850VA)
LED Status (1200/1500/2000VA)
Alarm
Normal
LED lighting
LED lighting
Off
Battery Discharge
Flash once every 30 seconds
LED lighting
Beep once every 30 seconds
Battery Low
Flash once every 2 seconds
LED lighting
Beep once every 2 seconds
Overload
Flash once every 0.5 second
LED lighting
Beep once every 0.5 seconds
Off charging mode
LED off
LED off
Off
Fault
LED off
LED off
Continuous alarm
TROUBLE SHOOTING
Problem
Possible Cause
Solution
Batteries are not fully charged.
Recharge the battery by leaving the UPS plugged in.
The UPS does not
perform expected
runtime
Battery is slightly worn out.
Contact Technical Support.
The on/off switch is designed to prevent
Turn the UPS off. Wait 10 seconds and then turn the
damage by rapidly turning it off and on.
UPS on.
The unit is not connected to an AC outlet.
The unit must be connected to a 230Vac 50/60Hz outlet.
The battery is worn out.
Contact Technical Support.
The UPS will not turn
on.
Mechanical problem.
Contact Technical Support.
Turn the UPS off and unplug at least one piece connected
Circuit breaker is tripped due to overload
equipment. Unplug the power cord of the UPS then press
the circuit breaker knob.
Batteries are discharged
Allow the unit to recharge for at least 4 hours.
Unit has been damaged by a surge or
Contact Technical Support.
Outlets do not
provide power to
equipment
spike
Fault code F09
Output Short :
Output circuit short.
Shut down the UPS
Your attached equipment may have problems, please remove
them and check again.
Fault code F12
Battery voltage is too low.
Shutdown your computer and recharge the battery immediately.
Fault code F13
Battery is overcharged.
Contact Technical Support.
Fault code F14
Overload occurs:
Your equipment requires more power than
the UPS can provide. It will shutdown.
Shut off non-essential equipment.
If this solves the overload problem, the UPS will transfer to
normal operation.
SOFTWARE DOWNLOAD
Power Master management software provides a user-friendly interface for your power systems. The graphic user interface is
intuitive and displays essential power information at a glance. Please follow procedure below to install the software.
Installation procedure:
1. Download Power Master from the website:
http://www.powermonitor.software/
2. Double-click the file and follow the installation steps.
When your computer restarts, the Power Master
software will appear as a blue icon located in the
system tray.
All rights reserved. Reproduction without permission is prohibited
All manuals and user guides at all-guides.com