Makeblock mDrawBot Kit, User Manual

Page: 3 / 20

Part List
3 × Beam0324 - 184
2 × Beam0824 - 096
1 × Beam0824 - 032
3 × Bracket 3 × 3
3 × Plate 3 × 6
1 × Bracket U1
4 × Timing Pulley Slice 90T
2 × 42BYG Stepper Motor Bracket
2 × Plastic Timing Pulley 90T
2 × Tire 90T B
1 × Caster Wheel
2 × Rubber Blanket
2 × Shaft Connector 4mm
2 × Timing Pulley 18T
1 × Pen Holder and V Clamp
2 × 2 inch G Clamp
1 × Plastic Hinge
1 × Plastic Hinge Gasket
1 × Spring 0.6 × 6 × 50
1 × Threaded Shaft 4 × 39mm
1 × Circle Shaft 4 × 80mm
2 × Shaft Collar 4mm
5 × Flange Bearing 4 × 8 × 3mm
1 × Square Nut M4
3 × Nylon Cap M4
1 × Polyester Thread(8m)
2 × Timing Belt 112MXL
1 × Cross&2.5mm HEX Screwdriver
1 × Rubber Bank
1 × HEX Key 1.5mm
1 × Wrench 5mm&7mm
26 × Screw M4 × 8
42 × Screw M4 × 16
5 × Screw M4 × 22
1 × Screw M4 × 35
6 × Headless Set Screw M3 × 5
8 × Countersunk Screw M3 × 8
50 × Nut M4
4 × Nylon Stud M4 × 30
2 × Plastic Ring 4 × 8 × 1mm
8 × Plastic Ring 4 × 7 × 3mm
4 × Plastic Ring 4 × 7 × 10mm
1 × 9g Micro Servo Pack
2 × 42BYG Stepper Motor
2 × Base Bracket
1 × Battery Holder
1 × Makeblock Orion
2 × Me Stepper Motor Driver
1 × RJ25 Adapter
1 × AC/DC Adapter 12V2A
2 × 6P6C RJ25 Cable - 20cm
1 × 6P6C RJ25 Cable - 35cm
1 × Micro USB Cable
1 ×
9g Servo Extension Cord
2 × Plastic Rivet R4060
4 × Plastic Rivet R4120
10 × Nylon Cable Tie 2 × 100
※ All pictures in this manual do not
represent the actual scale of them .
3
※ Warning : Keep this kit out of the reach of children or animals .
Small parts may cause choking or serious injury if swallowed .
1 9
mSpider
24
mEggBot
31
mCar
35
Wiring and Software
mEggBot is one form of this four-in-one
drawbot which enables you to draw on
an egg or a ping-pong. Refer here to see
the assembly of mEggBot.
mCar is one form of this four-in-one
drawbot which enables you to draw on the
ground. Refer here to see the assembly of
mCar.
To enable the Drawbot to move, it's
required to use the software mDraw with
the Drawbot. Refer here to see the
instruction for wiring, software, and
related details. mSpider is one form of this four-in-one
drawbot which enables you to draw on
a blackboard or a wall. Refer here to
see the assembly of mSpider. ·
· · ·
1 ×
tape 100cm
（
Paper
）
2