Majestic SD 236BT/RDS/USB/AX, Instruction Manual

Page: 6 / 6

Page 5 Page 6
received yet.
When AF switching mode is selected, the radio checks the signal strength of AF
all the time. The interval of checking time of each AFs depends on the signal
strength of current station, from a few minute for strong station to a few seconds
for weak station. Every time that new AF is stronger than current station, it switches
over to that frequency for very short time, and NEW FREQUENCY is displayed for
1-2 second. Because the mute time of AF switching or checking time is very short,
it is almost inaudible in case of normal program.
During FM mode, when AF is on, SEEK, (SCAN), AUTO-MEMORY function can
only receive and save RDS program.
When pressed long, AF mode is converted to REGION ON/OFF mode.
REGIONAL MODE ON:
AF switching or PI SEEK is implemented to the station which have all PI codes
are same as current station.(PI CODE is checked when AF CHECK in progress)
REGIONAL MODE OFF:
The regional code in the format of PI code is ignored when AF switching or PI
SEEK is implemented.
(PI CODE and COVERAGE AREA is not checked when AF CHECK in progress)
12. TA [TRAFFIC ANNOUNCEMENT] BUTTON
(1) When press the button, it is activated as TA mode on or off.
When TA mode is on(TA is displayed on LCD), it will begin to seek TA station
and TA SEEK will be displayed on LCD for a while.
When trafc announcement is transmitted:
1) If the unit is in SD, USB or disc mode, it will switch to radio mode temporarily.
2) Temporarily switch over to an EON linked station when EON detects a trafc
announcement on that other program, and TP will be displayed on LCD
3) If volume level is below 20, volume level is raised to 20, and returns to its previous
mode and volume level when the trafc announcement is over.
If volume is adjusted during trafc announcement, only the trafc announcement
volume is valid.
* TA interruption function:
The current trafc announcement is cancelled by pressing this key. But the
TA mode will not be off.
* When TA is on, SEEK, (SCAN), AUTO MEMORY function can be received or
saved only when trafc program identication code has been received.
When TA is ON, trafc program identication code is not received during
specied time.
(2) When pressed long, it is selected EONTA LOCAL/EONTA DISTANCE mode.
The purpose of this key is to reduce unwanted EON TA switching, which EON TA
information was received from current station and the radio switched to that EON
linked station, but no information could not be received because the EON linked
station is located too far from that area. So the radio is switched back to current
station again.
In above operation, a customer listen to a wrong program or mute sound for a while.
1) EONTA LOCAL mode:
When the led strength level of EON linked is less than the threshold level, the
When EONTA DISTANCE mode is selected, EONTA DX on numeric display
is indicated for a few seconds.
radio does not switch that station, and a customer can hardly listen to any
disturbances.
When EONTA LOCAL mode is selected, EONTA LO on numeric display is indicated
for a few seconds.
2) EONTA DISTANCE mode:
EON TA switching is try to implemented by the information of current station.
13. PTY (PROGRAM TYPE) BUTTON
Press it briey and repeatedly to select one of the following mode:
POP M- - NEWS
While selecting PTY TYPE, its selection is implemented by preset buttons as
described in preset key. (press one of the 6 preset buttons shortly and repeatedly
to select the PTY TYPE in the preset button) When POP M or NEWS is on, the
previous PTY program and PTY word is displayed on LCD. If there are no keys
entered for 2 seconds, previously selected PTY is searched. During 1 loop, if
desired PTY is not found, NO PTY is ashed, then return to previous normal radio
and PTY icon goes of
f.
14. 0 DSP BUTTON
Press 0 DSP button to view all the current status
.
EQ BUTTON
Press EQ button to turn on equalization function and to select desired audio mode
:
→ FLAT → POP → ROCK → CLAS → EQ OFF
16. AUX INPUT JACK
Press the mode button to select auxiliary input playing mode. Then you can
connect any matched external audio device to this socket. Use the volume
knob to adjust volume.
17. # SCAN
18. T-MENU TRANS
19. USB SOCKET
When needing to play the le in the USB stick, turn over the plastic cover cap
then insert the USB stick into the USB socket. The system will change into the
USB mode automatically
,
and then play the rst le in the USB.
When no needing to do USB operation, please cover the plastic cover cap.
20. SD CARD SLOT
When you need to play the le in the SD card, insert the SD card into the card
slot. The system will change into the SD mode automatically
,
and then play the rst
le in the SD.
Note:
When SD card and USB stick are both inserted into their slot or socket, the system
will change into the USB mode automatically.
21. RESET BUTT ON
Before operating the unit for the rst time, or after replacing the car battery or
changing the connections. You must reset the unit.
Press this button with a cuspidal object. This operation will erase the clock
setting and some stored contents.
Press #SCAN button (17) to enter scan mode, the unit will scan to higher frequency
station and keep on each station for several seconds (the corresponding frequency
will ash 5 times on LCD).
15. BUTTON
pick up the phone