background image

Models: 
380IDVNVC & 380IDVPVC
490IDVNVC & 490IDVPVC

IDV Series Direct Vent 
Gas Fireplace Insert

57D0215  9/10  Rev. 11

Installation and 
Operating Instructions

WARNING

IF the INFORMAtION IN theSe INStRuCtIONS IS NOt 
FOllOWeD  exACtly,  A  FIRe  OR  exPlOSION  MAy 
ReSult  CAuSING  PROPeRty  DAMAGe,  PeRSONAl 
INjuRy OR lOSS OF lIFe.

– 

Do  not  store  or  use  gasoline  or  other  flammable 
vapors and liquids in the vicinity of this or any other 
appliance.

–  WhAt tO DO IF yOu SMell GAS

 

•  Do not try to light any appliance.

 

•  Do not touch any electrical switch; do not use any 

phone in your building.

 

•  Immediately call your gas supplier from a neighbor's 

phone. Follow the gas supplier's instructions.

 

•  If you cannot reach your gas supplier, call the fire 

department.

–  Installation  and  service  must  be  performed 

by  a  qualified  installer,  service  agency  or  the 
gas supplier.

WARNING: Improper installation, adjustment, alteration, 
services  or  maintenance  can  cause  injury  or  property 
damage. Refer to this manual. For assistance or additional 
information consult a qualified installer, service agency 
or the gas supplier.   

this  appliance  may  be  installed  in  an  aftermarket*, 
permanently located, manufactured home (uSA only) or 
mobile home, where not prohibited by local codes.
this  appliance  is  only  for  use  with  the  type  of  gas 
indicated  on  the  rating  plate.  this  appliance  is  not 
convertible for use with other gases, unless a certified 
kit is used. 

*  Aftermarket: Completion of sale, not for purpose of resale, from the 

manufacturer.

Due tO hIGh teMPeRAtuReS, the APPlIANCe 
ShOulD  Be  lOCAteD  Out  OF  tRAFFIC AND 
AWAy FROM FuRNItuRe AND DRAPeRIeS.

ChIlDReN AND ADultS ShOulD Be AleRteD 
tO   t h e   h A Z A R D S   O F   h I G h   S u R FA C e 
teMPeRAtuRe AND  ShOulD  StAy AWAy  tO 
AVOID BuRNS OR ClOthING IGNItION.

yOuNG  ChIlDReN  ShOulD  Be  SuPeRVISeD 
WheN they ARe IN the SAMe ROOM AS the 
APPlIANCe.

ClOthING OR OtheR FlAMMABle MAteRIAl 
ShOulD  NOt  Be  PlACeD  ON  OR  NeAR  the 
APPlIANCe.

KeeP the ROOM AReA CleAR AND FRee FROM 
COMBuStIBle  MAteRIAlS,  GASOlINe,  AND 
OtheR FlAMMABle VAPORS AND lIquIDS.

INStAlleR: leave this manual with the appliance.
CONSuMeR: Retain this manual for future refer-
ence.

570215
380IDV cover

Summary of Contents for 380IDVNVC









































Reviews: