Majestic fireplaces NVBC42 Installation & Operation Instructions Download Page 1

Decorative Gas Appliances

INSTALLER: DO NOT DISCARD THIS MANUAL - Leave in fireplace for homeowner.

PLEASE READ THIS MANUAL

BEFORE INSTALLING AND

USING APPLIANCE.

IMPORTANT: Read all instruc-
tions and warnings carefully
before starting installation.
Failure to follow these instruc-
tions may result in a possible
fire hazard and will void the
warranty.

WARNING: If the information in
this manual is not followed
exactly, a fire or explosion may
result causing property dam-
age, personal injury or loss of
life.

FOR YOUR SAFETY
Installation and service must
be performed by a qualified
installer, service agency, or the
gas supplier. Do not store or
use gasoline or other flam-
mable vapors and liquids in the
vicinity of this or any other
appliance.

FOR YOUR SAFETY
If you smell gas:
1. Open windows
2. Do not touch electrical

switches.

3. Do not try to light any appli-

ance.

4. Extinguish any open flame.
5. Do not use the phone in

your building.

6. Immediately call your gas

supplier from a neighbor's
phone.

7. Follow your gas supplier's

instructions.

8. If you cannot reach your gas

supplier, call the fire depart-
ment.

INSTALLER/CONSUMER

SAFETY INFORMATION

Models: NVBR36, NVBC36

NVBR42, NVBC42

Homeowner's Installation and

Operating Manual

DESIGN

CER

TIFIE D

7412950  9/03  Rev.  12

NVBR36

NVBC42

950

Summary of Contents for NVBC42

























Reviews: