50
DV360/580 Series Direct Vent Gas Fireplace
20010667
For Use in Mobile Homes: Model DV360RMH
This appliance may be installed as an OEM installation in a manufactured home (US only), or a mobile
home; it must be installed in accordance with the manufacturer’s instructions and the manufactured
home construction and safety standard Title 24 CFR Part 3280, or Standard for Installation in Mobile
Homes CAN/ CSA Z240 MH.
This appliance is only for use with the type(s) of gas indicated on the rating plate. A conversion kit is sup-
plied with the appliance.
This gas fireplace should be installed by a qualified in-
staller in accordance with local building codes, and with
current CSA-B149.1 Installation codes for Gas Burning
Fireplaces and Equipment, and CAN/
CSA Z 240.4 Canada.
A manufactured home (US only) or mobile home
OEM installation must conform with the Manufactured
Home Construction and Safety Standard, Title 24 CFR
Part 3280, or when such a standard is not applicable,
the Standard for Manufactured Home Installations
ANSI/NCSBCS A225.1, or Standard for Gas Equipped
Recreational Vehicles and Mobile Housing
CSA Z240.4.
The appliance when installed, must be electrically
grounded in accordance with local codes or, in the ab-
sence of local codes, with the current National Electri-
cal Code, ANSI/NFPA 70, or the Canadian Electrical
Code, CSA C22.1.
FOR SAFE INSTALLATION AND OPERATION
PLEASE NOTE THE FOLLOWING:
1. This fireplace gives off high temperatures and
should be located out of high traffic areas and away
from furniture and draperies.
2. Children and adults should be alerted to the hazards
of fireplace high surface temperatures and should
stay away to avoid burns or ignition of clothing.
3. Children should be carefully supervised when in the
same room as your fireplace.
4. Under no circumstances should this fireplace be
modified. Parts removed for servicing should be
replaced prior to operating this fireplace again.
5. Installation and any repairs to fireplace should be
performed by qualified installer, service agency or
gas supplier. A professional service person should
be contacted to inspect fireplace annually. More
frequent cleaning may be required due to excess lint
and dust from carpeting, bedding material, etc.
6. Control compartments, burners and air passages
in this fireplace should be kept clean and free of
dust and lint. Make sure that the gas valve and pilot
light are turned off before you attempt to clean this
fireplace.
7. The venting system (chimney) of this fireplace
should be checked at least once a year and if
needed your venting system should be cleaned.
8. Keep the area around your fireplace clear of com-
bustible materials, gasoline and other flammable
vapor and liquids. This fireplace should not be used
as a drying rack for clothing, nor should Christmas
stockings or decorations be hung on or around the
fireplace.
9. Under no circumstances should any solid fuels
(wood, coal, paper or cardboard etc.) be used in this
fireplace.
10. The flow of combustion and ventilation air must not
be obstructed in any way.
11. When the fireplace is installed directly on carpet-
ing, vinyl tile or any combustible material other than
wood, the fireplace must be installed on a metal or
wood panel extending the full width and depth of the
fireplace.
12. This fireplace requires adequate ventilation and
combustion air to operate properly.
CFM Corporation Model DV360RMH must
be firmly attached to the building.
Conversion Instructions
1. Discount power to unit and shut off the gas supply.
2. Remove the window frame assembly (see ‘Window
Frame Assembly’ section).
3. Carefully remove the logs.
4. Remove the pilot assembly from bracket.
5. Remove the screws which are holding the burner
housing assembly in place.
6. Remove the burner housing assembly.
7. Remove the main and front orifice and replace with
the orifice supplied in the conversion kit. Use the
small orifice size for the front burner and the bigger
orifice size for the main burner.
8. Remove the compression fitting which holds the alu-
minium tubing in the pilot assembly. This will reveal
the pilot orifice which must be replaced with the one
provided in the conversion kit.
9a. Units with SIT valve
(Refer to illustrations in the
installation instructions supplied with the kit):
