Main Combi 25 Eco Elite Installation & Service Manual Download Page 19

Page: 19 / 56

7.0 Site Requirements

7.7

Condensate Drain

(cont.)

12. A boiler discharge pump is available, ‘MULTIFIT’

part no. 720648301. This pump will dispose of both

condensate & high temperature water from the relief valve.

It has a maximum head of 5 metres. Follow the instructions

supplied with the pump.

13. Condensate Drain Pipe ‘Trace Heating’ Elements are

available in various lengths. ‘MULTIFIT’ part nos.:-

1 metre 720644401

2 metre 720664101

3 metre 720664201

5 metre 720664401*

*Where the drain is between 3 & 5 metres a 5 metre kit can

be used and “doubled back” upon itself.

14. It is possible to fit the element externally on the

condensate drain or internally as detailed in the instructions

provided.

15. The fitting of a ‘Trace Heating’ Element is NOT a

substitute for correct installation of the condensate drain.

ALL requirements in this section must still be adhered to.

Boiler

vi) pumped into an external soil & vent pipe

2.5° Minimum fall

50mm per metre of pipe run

Condensate Pump

Unheated Location
(e.g. Garage)

Basement or similar
(heated)

Boiler

2.5° Minimum fall

50mm per metre of pipe run

Pipe must terminate above
water level but below
surrounding surface. Cut
end at 45°

The ‘Trace Heating’ element
must be installed in accordance
with the instructions supplied.
External runs & those in
unheated locations still require
insulation.

vii) to a drain or gully with extended

external run & trace heating

Boiler

v) pumped into an internal discharge branch

(e.g. sink waste) downstream of the trap

Pipe must terminate above
water level but below
surrounding surface. Cut
end at 45°

2.5° Minimum fall

50mm per metre of pipe run

Condensate Pump

Sink

Basement or similar
(heated)

Summary of Contents for Combi 25 Eco Elite

























































Search results

Summary of Contents for Combi 25 Eco Elite

Reviews:

Related manuals for Combi 25 Eco Elite

Brands by name

Popular brands

Main Combi 25 Eco Elite, Installation & Service Manual

Search results

Summary of Contents for Combi 25 Eco Elite

Reviews:

Related manuals for Combi 25 Eco Elite

Brands by name

Popular brands