Mahindra 10 Cab Series 4510C Operator'S Manual Download Page 35

Page: 35 / 115

TO PROTECT ENGINE AND
HYDRAULIC COMPONENTS.

●

Idle engine for 1 minute

before shut down or full load

operation.

●

Do not exceed 1/2 throttle for

first 5 minutes of operation.

CAUTION

KEEP HANDS

AND

CLOTHING

AWAY FROM

ROTATING

FAN AND

BELTS TO

PREVENT

SERIOUS

INJURY

Warning

Location: On Dash cover side RH

Part No.: 1260-904-064-0

Location: On Radiator bracket

side LH&RH

Part No.: 1260-904-061-0

The cooling system Operates

under pressure .

●

It is dangerous to remove the

radiator cap while the system

is hot

●

Always turn the cap slowly to

the first stop and allow pressure

to escape before removing the

cap completely.

●

When operating below 32°F, use

suitable anti-freeze solution as

coolant

Warning

BEFORE OPERATE THE

TRACTOR, READ THE

OPERATOR’S MANUAL

THOROUGHLY, TO

UNDERSTAND THE

IMPORTANT FUNCTIONS

AND CONTROLS.

CAUTION

Location: On Radiator

bracket side LH&RH

Part No.: 1260-904-063-0

Location: On dash cover side LH.
Part No.: 1260-904-067-0A

DANGER

Rotating driveline contact can
cause Death

KEEP AWAY !

Keep all drive line.

Tractor and equipment shields in
place during operation

Location: On PTO Guard
Part No.: 1200-910-013-0

Summary of Contents for 10 Cab Series 4510C




















































































































Search results

Summary of Contents for 10 Cab Series 4510C

Reviews:

Related manuals for 10 Cab Series 4510C

Brands by name

Popular brands

Mahindra 10 Cab Series 4510C, Operator'S Manual

Search results

Summary of Contents for 10 Cab Series 4510C

Reviews:

Related manuals for 10 Cab Series 4510C

Brands by name

Popular brands