Magtrol HD-106-1 User Manual Download Page 2

1st Edition, rev. B – December 2008

While every precaution has been exercised in the compilation of this document to 
ensure the accuracy of its contents, Magtrol, Inc. assumes no responsibility for errors or 
omissions.  Additionally, no liability is assumed for any damages that may result from the 
use of the information contained within this publication.
 

COPYRIGHT

Copyright ©1999-2008 Magtrol, Inc.  All rights reserved.
Copying or reproduction of all or any part of the contents of this manual without the 
express permission of Magtrol is strictly prohibited.

Purchase Record

Please record all model numbers and serial numbers of your 
Magtrol equipment, along with the general purchase information.  
The model number and serial number can be found on either 
a silver identification plate or white label affixed to each unit.  
Refer to these numbers whenever you communicate with a 
Magtrol representative about this equipment.

Model Number: 

_____________________________

Serial Number: 

_____________________________

Purchase Date: 

_____________________________

Purchased From: 

_____________________________

Summary of Contents for HD-106-1





















Reviews: