background image

5.3 Definition of Tampering and Recommendations

Motor

Sensors

Controller

Electric cables
Controls on the handlebar 

Display

Battery

Battery charger

Frame

Fork(including suspension)

Hubmotor wheel 

Brake system
 
Brake shoe

Luggage carrier

Bottom bracket

Cranks

Wheel without hub motor

Chain or belt (at original 
width)

Rim tape

Tires (at orginal ETRTO 
specifications only)

Mechanical / hydraulic 
brake cables

Brake system (for drum, 
disc and roller brakes)

Handlebar and stem 
(without alterations to the 
handlebar and stem)

Saddle and seat post 
(maximum variation from 
original should not exceed 
20mm)

Headlight

Headset

Pedals (at the same width 
as the originals)

Derailleurs

Shifters

Shifting inner/outer cables

Chainring / belt drive ring

Cassette / freewheel or 
cogs (when the cogs are 
the same as the originals)

Chaincase

Mudguards (only the same 
size as the originals and 
mounted at least 10 mm 
distance from the tire)

Spokes
Inner tubes
Dynamo
Front light / front reflector
Rear light / rear reflector
Wheel reflectors
Kickstand
Grips (with a screw clamp 
only)

Components which can 
only be replaced after 
approval from the bicycle 
manufacturer/ electronic 
system provider

Components which can 
only be replaced after 
approval from the bicycle 
manufacturer

Components which can 
only be replaced after 
approval from the bicycle 
or component manufactur-
er

Components which can be 
replaced without approval

Category 1

Category 2

Category 3

Category 4

      WARNING:

 

Modifications to any part of your bike, such as the fork or frame, may make that part or the entire bike unsafe. A poorly 
installed or modified component can increase the stress on all other parts, greatly increasing their chance of failure. 
Modifications can also adversely affect the handling of your bike, resulting in loss of control, falls and serious injury. 
Please do not add, remove, or modify parts of your bike in any way before consulting with a trained bike technician. We 
recommend you consult with us at before you make modifications or add parts, in order to confirm their safety and 
compatibility with your bike. 

RECOMMENDATIONS AND MAINTENANCE

19

Summary of Contents for Payload

























Reviews: