2
Magnum Innovations 5675 Hudson Industrial Pkwy, Suite 3 Hudson, OH 44236 phone 330.915-2382 fax 330.529.5279 www.magnum-innovations.com [email protected]
Product Installation Guide
8] Comissioning
Part 1:
Activate commissioning (or linking) mode for a system compatible with the switch.
If you don’t know how to do this, consult the manual for the compatible system or contact the manufacturer for
assistance.
Part 2:
Put the switch into commissioning mode.
To enter commissioning mode, start by selecting one button on the switch. (Use the same button for the entire
sequence. Pressing any other button will exit the commissioning mode.)
Next, execute the following long-short-long sequence:
1.Press and hold the selected button for more than 7 seconds before releasing it
2.Press the selected button quickly (hold for less than 2 seconds)
3.Press and hold the selected button again for more than 7 seconds before releasing it
The switch has now entered commissioning mode.
Part 3:
Linking the switch to the compatible system.
A radio signal needs to be sent from the switch to the compatible system on the correct ZigBee channel. The
system uses one of sixteen possible channels, automatically set by the system. Using the switch, a signal will
be sent on each channel until the channel used by the compatible system is found. Upon entering commis-
sioning mode, the switch sends a signal on the currently selected channel. The signal is sent on the default
channel 11, unless the switch had been put on another channel previously. (This allows linking additional
devices without changing the currently used radio channel.)
Here is a chart of the ZigBee channels and the corresponding radio frequencies (in MHz).
Cycle throught the sixteen channels
To change the switch’s channel, short press the selected switch button
(less than 7 seconds) once
after entering commissioning mode. This will
reset the channel used by the switch to channel 11.
If the switch was already operating on channel 11 (default condition)
then the radio channel will remain unchanged. This ensures that the
switch will always use channel 11 as the starting point for the channel
adjustment.
Short press the selected button (less than 7 seconds) again to move to
the next channel. For each such button press, the switch transmits on
the next channel.
If channel 26 has been reached then channel 11 will
be used next.
When the switch is on the correct channel, the compatible system will
provide a link confirmation indication.
Consult the instructions for the
compatible system for details of the link confirmation indication. There
should be a visible or audible exchange indicated on the system, and the
switch will be linked to the system.
Exit linking mode on the switch by pressing any other button on the switch.
For problems with the compatible system, please contact the system
provider.
11] Compliancy
This device complies with part 15 of the FCC rules and Industry Canada ICES-003. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
IMPORTANT
! Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2)
l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, meme si le brouillage est susceptible
d’en compromettre le fonc- tionnement.
IMPORTANT!
Tous les changements ou modifications pas expressément approuvés par la partie responsable de
la conformité ont pu vider l’autorité de l’utilisateur pour actioner cet équipment.
10] Warranty
U.S. Two-year Limited Warranty:
Products purchased in the U.S.A. are warranted for two years from date of purchase
by Magnum Energy Solutions, LLC (M.E.S.) to be free of defects in materials and workmanship. In the event of
such defect, product will be repaired promptly without charge or, at our option, replaced with a new product of
equal or superior value if delivered to M.E.S. or an Authorized Service Center, prepaid, together with the sales slip
or other proof of purchase date. This warranty excludes defects due to normal wear, abuse, shipping damage, or
failure to use product in accordance with instructions. This warranty is void in the event of unauthorized repair or
modification, or removal or defacing of the product labeling. The MES warranty specified herein covers material
only and does not include labor or incidental costs associated with product replacement or repair.
9] Troubleshooting
PROBLEM
WHAT TO CHECK
The rocker pad does not generate a message
Verify the rocker pad is installed in the proper orientation
The linked device does not respond to wireless
messages
• Check for environment or range issues
• Verify the device is linked
• Check the transceiver connection and the wiring for errors
• Check if appropriate devices are linked according to
good system planning
