Magnum MI-76150 Operating Manual Download Page 3

2

ASSEMBLY INSTRUCTIONS 

MAGNUM INDUSTRIAL MI-76100 & MI-76150 DRILL PRESSES

Before you assemble your drill press, review the parts breakdown and keep it ready for reference.

Start by removing the parts from the packaging.

Carefully check the packaging for small pieces before you continue.

Lay out the parts on a large, clear and unobstructed area and ensure that all parts are accounted for.

If you have any questions or require further information, please contact the KMS Tools Service Department at 604.395.4134
or email 

[email protected]

ASSEMBLING THE DRILL PRESS

1. Bolt the 

BASE FLANGE (4)

 and 

COLUMN (19) t

o the 

BASE (1).

2. Carefully remove the 

RACK COLLAR (21)

 from the 

COLUMN (19)

. Apply even pressure and gently slide the 

COLLAR

. Using

too much force can cause the 

COLLAR

 to bind. If it is tight, try gently tapping the 

COLLAR

.

3. Ensure that the 

WORM GEAR (10)

 and 

HELICAL GEAR (9)

 are installed in the 

TABLE BRACKET (7)

 and have not fallen out

during unpacking.

4. Place the 

RACK (18)

 into the 

TABLE BRACKET (7)

. The tapered end of the

 RACK

 faces upward and the square end faces

downward.

5. Lower the 

RACK (18)

 and the 

TABLE BRACKET (7)

 onto the 

COLUMN (19)

. Take care to hold the two pieces together. This 

may require two people.

6. Fit the bottom lip of the 

RACK (18)

 in the friction ring on the 

BASE FLANGE (4)

. Secure the top of the rack by installing the

RACK COLLAR (21)

. Tighten the 

SET SCREW (20)

 in the 

RACK COLLAR (21)

. Take care not to over tighten.

7. Slide the 

CRANK SLEEVE HANDLE (6)

 on the 

WORM GEAR (10)

 and secure it with the 

SET SCREW (5)

.

8. Lower the 

HEAD (26)

 to the 

COLUMN (19)

 and secure the 

HEAD (26)

 by tightening two 

SET SCREWS (26-1)

. This may

require two people.

9. Secure the 

TABLE (17)

 onto the 

TABLE ARM (12)

.

10. Attach a 

HANDLE KNOB (23)

 to each of the three 

FEED HANDLES (22)

. Then secure the 

HANDLES (22)

 to the 

PINION

SHAFT (24)

.

11. Thread a light bulb (maximum 40 watts) into the 

LAMP HOLDER (32)

. (Light bulb sold separately.)

12. Remove the protective coating from all surfaces using a rag dipped in environmentally safe degreaser

INSTALLING THE CHUCK

1. Degrease all pieces. Slide the 

ARBOR (53)

 into the 

SPINDLE (51)

, flat end up.

2. Slide the 

CHUCK (54) 

over the tapered end of the 

ARBOR (53)

 and, using a wooden mallet, give the 

CHUCK

 a good tap. The

taper is designed to hold the 

CHUCK

 securely in place.

Summary of Contents for MI-76150












Reviews: