3
Magnum First - 1930 Baseline Road, Grand Island, NY 14072 - phone 716-293-1588 - www.magnumfirst.com - [email protected]
Product Installation Guide
7] Warnings & Cautions
8] Warranty
5] General Operation (continued)
6] Technical Specifications
Factory setting operation:
When entering the room, the wireless receiver control switch will need to be manually turned ON. Once learned
into the receiver switch, the Wireless occupancy sensor will send messages to the receiver switch, keeping the
lights on until the room is vacant. Once the occupancy sensor stops sending messages and the receiver time
out period expires the lights will turn OFF.
Time-Outs:
When used with an occupancy sensor the ILS2 has four time-out settings: 2 (test), 10, 20, or 30 min. (a longer
timeout is recommended when using self-powered devices in dark spaces). The time-out duration is user selected
through the use of the Dip Switch Settings. NOTE: Since the sensor is only sending a message every one to two
minutes, the 2 minute time delay is not sufficient for normal operation.
Walk-Through Time Delay:
The walk-through feature is only active in the Auto-ON/Auto-OFF mode with time delay > 2 minutes. This
feature is useful when a room is momentarily occupied. When enabled, the ILS2 will turn the lights OFF shortly
after the person leaves the room. The walk-through feature works in the following manner: When a person
enters the room, the lights will turn ON. If the person leaves the room before the walk-through time-out of 2.5
minutes, the Sensor will turn the lights OFF within 2.5 minutes of no occupancy detected. If the room is occupied
for longer than 2.5 minutes, the Sensor will enter the Occupied Mode with the time-out duration specified by
the Dip Switch settings.
• TO AVOID FIRE SHOCK OR DEATH; TURN OFF POWER at circuit breaker or fuse and test that power is off
before wiring, servicing, installing or removing device.
• ILS2 products do not require a neutral wire. There is a minimum load requirement of 25 Watts for these products.
• To be installed and/or used in accordance with electrical codes and regulations.
• If you are unsure about any part of these instructions, consult an electrician.
• Recommended minimum wall box depth is 2-1/2”.
• Use this device with copper or copper clad wire only.
U.S. Two-year Limited Warranty:
Products purchased in the U.S.A. are warranted for two years from date of purchase
by Magnum Innovations to be free of defects in materials and workmanship. In the event of such defect, product
will be repaired promptly without charge or, at our option, replaced with a new product of equal or superior value
if delivered to Magnum or an Authorized Service Center, prepaid, together with the sales slip or other proof of
purchase date. This warranty excludes defects due to normal wear, abuse, shipping damage, or failure to use
product in accordance with instructions. This warranty is void in the event of unauthorized repair or modification,
or removal or defacing of the product labeling. The Magnum warranty specified herein covers material only and
does not include labor or incidental costs associated with product replacement or repair.
Part Numbers (Frequency Dependant)
M9-ILS2 (902 MHz - North America)
M8-ILS2 (868 MHz - Europe and China)
MJ-ILS2 (928 MHz - Japan)
Modulation Type
FSK (Frequency Shift Keying)
Operational Temperature
0° to +40°C
Power Consumption (< 1 Watt)
120VAC @6.2mA AC (330mW typical)
277VAC @4.5mA AC (460mW typical)
Addressing
Factory set unique ID (1 of 4 billion)
ETL Certified to UL Standard
UL-508, CAN / CSA-C22.2 No. 14
Radio Certification
FCC Part 15 Subpart C
IC RSS-Gen Issue 2, RSS-210 Issue 7, RSS-102 Issue 4
Contains FCC ID: SZV-STM300U Contains IC: 5713A-ST-
M300U
