manualshive.com logo in svg

Magnum 3005, Instruction Manual

The Cisco 3005 is a reliable and high-performing networking device designed to simplify your connectivity needs. Start using it effortlessly with the comprehensive "Getting Started" manual available for free download from manualshive.com. This user-friendly manual ensures seamless setup and operation for optimized performance.

Share
Download
background image

CONTENTS

•

         

 

Causes of failure

 

•

         

The calibration jig, heating element, sensor, or wiring may be faulty.

•

         

Check that the Soldering iron and Hot air pencil are properly inserted in their jig’s

•

         

When the calibration is complete the 

Complete

 LED on the PCCU will light and the 

Station will display 

CAL

•

         

Disconnect the Station and jig’s from the PCCU.

 

•

         

Reset the 3005 Station for new values to take effect.

 
 

SPECIFICATIONS

 

Mains input voltage:      220V – 240V  50/60Hz
 

Power consumption:      0.6 Amps           fuse 1A f/b

 

Output power:               24V 85W  + 24V85W

 

Air flow:                             1.5 to 6.5 litres/min

 
Temperature:               Soldering iron  100° to 450° ±  4 °C

                                      Hot air pencil   180° to 480° ±10 °C

                                 
Dimensions:                  L 250mm W 250mm  H 105    
 
Weight:                         4 KGS (8.8LBS)

 
 

 

 
 
 
 
 

file:///C|/Documents%20and%20Settings/Lauren...her%20stuff/magnum/3005%20word%20booklet.htm (11 of 12) [03/03/2003 10:16:31 PM]

Summary of Contents for 3005













Reviews:

No comments

Related manuals for 3005

Brands by name

Popular brands

Load more brands