manualshive.com logo in svg

Magnum Dimensions CSW2012-X, Owner'S Manual, Page: 30 / 46

Share
Download
Magnum Dimensions CSW2012-X Owner'S Manual Download Page 30

© 

2015 Sensata Technologies

 25

3.0 Operation

3.3.1 LED 

Indicators

The LED indicators on the front display panel are used to indicate the 

inverter’s status. Use Table 3-1 to determine the inverter status.

Table 3-1, Display Functions/Statuses

Status LED Display LED Display

Function/Status

Green

(solid)

Green

12.5

By-Pass mode. Display shows 

battery voltage in DC volts.

Amber

(solid)

Green

12.5

Inverter mode. Inverter running 

and display shows battery 

voltage in DC volts.

Amber

0.80

Inverte) mode. Inverter is 

running, and display shows 

output power in kW (800W as 

shown). The Select button has to 

be pressed.

Amber 

(

fl

 ashing)

Inverter mode. AC input is detected and the unit will 

switch to By-Pass mode within 20 seconds.

Red (solid)

OFF

E01-E12 Unit has shut down. Display 

shows an error code (see error 

code reference chart below).

3.3.2  Understanding the Power and Select Buttons

A beep sound occurs every time the Power or Select button is activated (i.e., 

pressed for 1 second).

Power button 

–

 

Turns the inverter On/Off during Inverter mode. Press and 

hold it for 1 second to turn the inverter either ON or OFF.

Note: The Power button can be used to turn the AC output off during AC By-

Pass mode with PS4 setting—without the need to disconnect the AC input as 

per the PS1 setting. See Table 3-2 or Section 3.3.3.
Select button 

– Used to check the inverter settings. Press the Select button 

several times to scroll down to view the inverter’s present setting.

Figure 3-1, Display Panel

3.3 

Display Panel Operation

This section provides information on the display panel (Figure 1-1, Item 5).

Summary of Contents for CSW2012-X















































Reviews:

No comments