manualshive.com logo in svg

Magnum Dimensions ACLD-40, Owner'S Manual, Page: 43 / 46

Share
Download
Magnum Dimensions ACLD-40 Owner'S Manual Download Page 43

© 

2015 Sensata Technologies

Page 36

Appendix A – Specifi cations and Optional Equipment

A-3  Optional Equipment and Accessories

The following components are available for use with the ACLD-40. Some of these items are required 

(depends upon the intended use of the inverter).

MMP Series Enclosures

The MMP175-30D, MMP175-60S, MMP250-30D, and MMP250-60S enclosures are for single inverter 

applications. The MMP Series enclosures have been speci

fi

 cally designed to combine all of the major 

components required for a renewable energy system—inverter/battery disconnect, AC overcurrent 

protection, grounding connections and a full system inverter bypass switch as a convenient way 

to isolate the inverter for battery maintenance—into a single, easy to install pre-wired enclosure.

MP Series Enclosures

The MPSL, MPSH, MPDH enclosures have been speci

fi

 cally designed to easily work with multiple 

stacked inverters. The MP enclosures feature convenient front-mounted AC and DC connections and 

easy front panel operation. Depending on the MP enclosure, you can connect from 2 to 4 inverters 

together—using the MPX Series extensions—to handle your power capacity needs. 

Advanced Remote Control

The ME-ARC remote control panel uses an LCD screen and at-a-glance LED’s to provide operating 

information and allow advanced features—if available—to be con

fi

 gured. This LCD remote control 

also provides advanced monitoring/troubleshooting and includes a FAVS button to quickly access 

your favorite features.

Battery Monitor

The Battery Monitor Kit (ME-BMK) is a single battery bank amp-hour meter 

that monitors the condition 

of the battery, provides information to let you know how much energy you have available, and lets 

you plan your electrical usage to ensure the battery is not being over-discharged. The ME-BMK-NS 

version does not include 

a DC shunt. You must order the ME-BMK to receive a 500A/50mv DC shunt.

Note: The DC shunt is included with MMP and MP Series enclosures. Order the ME-BMK-NS version 

when installed with the MMP or MP enclosures.

MagWeb

The MagWeb – Wireless (ME-MW-W) or MagWeb – Ethernet (ME-MW-E) are powerful and cost-

effective tools for remotely monitoring the inverter and accessories. Installed on the MagNet 

network, either MagWeb provides live internet monitoring of the inverter, battery monitor, and 

automatic generator start module. Using your always on Internet connection, either MagWeb 

makes live and historical conditions available to you.

MPX-CB Conduit Boxes

The MPX-CB Conduit Box is provided for installations where the electrical code requires the wiring 

to the ACLD to be enclosed and protected by conduit. The top side is designed to 

fi

 t MS-PAE Series 

inverters. It has conduit knockouts on each side and on the bottom.

A-2 Regulatory 

Compliance

The ACLD controller is designated as a “diversion controller”. It is used to divert excess power 

from a renewable energy source when connected in an AC coupled system. Even though used in 

an AC coupled system—and normally is connected to the utility grid—the ACLD-40 is not a grid-

interactive (also known as utility-interactive) device and does not have the capability to export 

(or sell) power back into the utility grid.
The ACLD controller is intended to be used for residential or commercial applications. It has 

been tested and listed to UL 1741, 2nd Edition (Inverters, Converters and Controllers for Use in 

Independent Power Systems) for use in the US; and is also certi

fi

 ed to CSA C22.2 No. 107.1-01 

(General Use Power Supplies) for use in Canada. It has been tested and certi

fi

 ed to these product 

safety standards by Intertek Testing Services (known as ETL), which is a Nationally Recognized 

Testing Laboratory (NRTL). NRTL’s are quali

fi

ed organizations that meet Occupational Safety and 

Health Administration (OSHA) regulations to perform independent safety testing and product 

certi

fi

 cation.

Summary of Contents for ACLD-40















































Reviews:

No comments