A1-4
Table A1-1. GPD 315 Parameters - Continued
SETTING RANGE
SETTING
FACTORY
USER
PARA.
CONSTANT
NAME
(AND UNITS)
INCREMENT
SETTING
SETTING
REF.
Analog Frequency Reference
n070
Filter Time Constant
0.00 to 2.00
0.01 s
0.10
(Voltage Ref Input)
n071
Analog Frequency Reference
-255 to 255
1%
100
Gain (Current Ref Input)
n072
Analog Frequency Reference
-100 to 100
1%
0
Bias (Current Ref Input)
Analog Frequency Reference
n073
Filter Time Constant
0.00 to 2.00
0.01 s
0.10
(Current Ref Input)
n074
Pulse Train Frequency
-255 to 255
1%
100
Reference Gain
n075
Pulse Train Frequency
-100 to 100
1%
0
Reference Bias
n076
Pulse Train Frequency Ref-
0.00 to 2.00
0.01 s
0.10
erence Filter Time Constant
0: Multi-Function analog input disabled
1: Aux. Frequency reference
n077
Multi-Function Analog
2: Frequency gain
1
0
Input Selection
3: Frequency bias
4: Voltage bias
n078
Multi-Function Analog Input
0: 0 - 10V
1
0
Signal Selection
1: 4 - 20 mA
n079
Multi-Function Analog Input
0 to 50
1%
10
Bias Setting
Carrier Frequency
1 to 4 (x 2.5 kHz)
1
4
5.5
7 to 9 (synchronous)
0: Not Provided
1: Continuous operation after power
Momentary Power Loss
recovery within 2 sec.
Ride-through Method
2: Continuous operation after power
1
0
5.16
recovery within control logic time
(no fault output)
Number of auto restarts
0 to 10
1
0
attempts
Prohibit Frequency 1
0.00 to 400.0
0.01 (Hz)
0.00
or 0.1 (Hz)
Prohibit Frequency 2
0.00 to 400.0
0.01 (Hz)
0.00
5.6
or 0.1 (Hz)
Prohibit Frequency 3
0.00 to 400.0
0.01 (Hz)
0.00
or 0.1 (Hz)
Prohibit Frequency Deadband 0.00 to 25.50
0.01 (Hz)
0.00
DC Injection Current
0 to 100
1 (%)
50
DC Injection Time at stop
0.0 to 25.5
0.1 (sec)
0.5
5.7
DC Injection Time at start
0.0 to 25.5
0.1 (sec)
0.0
Stall Prevention During
0: Enabled
1
0
Deceleration
1: Disabled
Stall Prevention During
30 to 200
1 (%)
170
5.23
Acceleration
Stall Prevention Level During
30 to 200
1 (%)
160
Running
Frequency Detection Level
0.00 to 400.0
0.01 (Hz)
0.00
5.19
or 0.1 (Hz)
Summary of Contents for GPD 315
