background image

Flex EX2 Quick Reference Manual

May 2018

Page 3 of 9

SERVICE INFORMATION

Your New Radio Remote Control System

Thank you for your purchase of Magnetek’s Flex EX2 Radio Remote Equipment Control. Magnetek has set 
a whole new standard in radio remote performance, dependability, and value with this unique new line of 
handheld transmitters.

If your product ever needs modification or service, please contact one of our representatives at the 
following locations: 

U.S. Service Information

For questions regarding service or technical information contact:
1-866-MAG-SERV
(1-866-624-7378)

International Service

262-783-3500

World Headquarters:

Magnetek, Inc.
N49 W13650 Campbell Drive 
Menomonee Falls, WI 53051

Telephone:

800-288-8178

Website:

www.magnetek.com

E-mail:

[email protected]

Fax Numbers:

Main:

800-298-3503

Sales:

262-783-3510

Service:

262-783-3508

© 2018 MAGNETEK

All rights reserved. This notice applies to all copyrighted materials included with this product, including, but 
not limited to, this manual and software embodied within the product. This manual is intended for the sole 
use of the person(s) to whom it was provided, and any unauthorized distribution of the manual or dispersal 
of its contents is strictly forbidden. This manual may not be reproduced in whole or in part by any means 
whatsoever without the expressed written permission of MAGNETEK.

Canada Service Information:

161 Orenda Road
Unit 1
Brampton, Ontario
L6W 1W3 Canada
Phone: 800-792-7253
Fax: 905-828-5707
416-424-7617 (24/7 Service pager)

EU Market Contact:

Brian Preston
Magnetek (UK) Ltd.
Unit 3 Bedford Business Centre
Mile Road
Bedford, MK42 9TW UK
Phone: +44-1234-349191
Fax: +44-1234-268955

Summary of Contents for FLEX EX2










Reviews: