22
English
Before you begin:
You must set
Home
in
Location
.
➟
p.29
Otherwise, personalized Picture and Sound settings will not be
memorized after the unit goes into Standby mode.
1
Press
MENU
and use
ɼɾ
to select
Sound
, then press
OK
.
2
Use
ɼɾɿɽ
to select the item you want to adjust, then press
OK
.
Adjust the Tonal Quality for each frequency.
This selects sound modes for more spatial or surround sound reproduction.
This function keeps a Constant Loudness Level between the TV
Commercials and the Programs.
You can select the Audio Output from the unit’s speakers or not. If your
amplifier is HDMI link function compatible and connected by an HDMI
cable to this unit, some sound operations such as volume up can be
changed by using this unit’s Remote Control.
You can select Audio Output through a Digital Audio Output connector.
You can set the Output mode as a default for the Sound mode (Analog
TV only).
This setting is not interlocked when you change the Output mode by
pressing
SAP
. Refer to
Switching Audio Mode
.
➟
p.18
Before you begin:
Make sure the unit is connected to Antenna or Cable.
1
Press
MENU
and use
ɼɾ
to select
Setup
, then press
OK
.
2
Adjust the following items.
Autoprogram
Be sure the RF cable is correctly connected to this unit and you are
registered with your cable TV provider when you install Cable channels.
1
Use
ɼɾ
to select
Autoprogram
, then press
OK
.
• If you run
Autoprogram
when you have Locked channels, a
message appears asking to enter your PIN. Enter your PIN in
order to complete the installation. You need to set the Channel
Lock again after the installation.
2
Use
ɼɾ
to select an appropriate option, then press
OK
.
– When
Antenna
is selected, the TV detects any off-the-air
antenna signals. It searches for ATSC (Digital) and NTSC
(Analog) channels available in your area.
– When
Cable
is selected, the TV detects signals supplied by
Cable. It searches for DTV, Analog TV and Cable channels
available in your area.
Auto sound
to select the desired setting, then press
OK
.
(
Personal
,
Standard
,
Vivid
,
Sports
,
Movie
,
Music
and
News
)
When you adjust the following settings (
Equalizer
,
SRS
TruSurround XT
and
Auto volume leveling
),
Personal
sound will be set automatically.
Equalizer
Cursor
ɾ
Cursor
ɼ
to Adjust each level of Tonal Quality
Press
BACK
to go back to the Previous Menu.
SRS TruSurround
XT
Off
to set SRS TruSurround XT
®
to Off
On
to set SRS TruSurround XT
®
to On
Auto volume
leveling
Off
to Remove the auto volume leveling
On
to Reduce Volume Differences between
the TV Commercials and the Programs
TV speakers
On
to Output Sound from the unit’s
Speakers
Off
no Output Sound from the unit’s
Speakers
CEC Link
to control Audio Output from your
connected fun-Link (HDMI CEC)
Compliant Devices with
VOL + /
ñ
by
using this unit's Remote Control.
Digital output
format
Multichannel
to Output Multichannel Signals.
(When the Audio of the content is PCM,
it will be Output in PCM even if
Multichannel
is selected.)
PCM
to Output PCM signals.
Sound
Picture
Sound
Setup
Features
Language
USB
Auto sound
Equalizer
SRS TruSurround XT
Auto volume leveling
TV speakers
Digital output format
Standard
On
Off
On
Primary MTS
Multichannel
Stereo
Primary MTS
Stereo
to Output Stereo Audio
Mono
to Output Mono Audio
SAP
to Output Second Audio Program
Setup
Picture
Sound
Setup
Features
Language
USB
Autoprogram
Channel list
Add channels
Antenna
Cable
Or
Picture
Sound
Setup
Features
Language
USB
Antenna
Back
Cable
Antenna
Cable
Autoprogram will rescan all channels.
Auto programming may take more than 20
minutes to complete.
Select your signal source.
ANTENNA IN
Continued on next page.
