Magna Telemotive blue PiraT Remote User Manual Download Page 75

Page: 75 / 82

Remote Control Touch / blue PiraT Re-

mote

User Guide

Datum:14.12.2018

Seite 75 von 82

RCTouch_UserGuide_V3.4.1.doc

11 Pinout of Remote Control Touch connector

As against to the Remote Control Voice, where the whole communication was send over this
cable, the

Remote Control Touch

only uses this cable for power.

Table 11.1: Contacts of the angeled Lemo plug

11.1 Contacts of the Remote Control Touch connection

This drawing shows the pinout of the

Remote Control Touch

cable.

Figure 11.1: Pins of the angeled LEMO plug (FGH.1B.308.CLAD42) at the cable

Lumberg KV81-8 Pin

(RCTouch)

Lemo Pin

(cabel)

Bananaplug Pin

Signal

blue

KL 15 (wake)

black

KL 31 (ground, -)

red

KL 30 (power, +)

Summary of Contents for Telemotive blue PiraT Remote



















































































Search results

Summary of Contents for Telemotive blue PiraT Remote

Reviews:

Related manuals for Telemotive blue PiraT Remote

Brands by name

Popular brands

Magna Telemotive blue PiraT Remote, User Manual

Search results

Summary of Contents for Telemotive blue PiraT Remote

Reviews:

Related manuals for Telemotive blue PiraT Remote

Brands by name

Popular brands