background image

CHAPTER 1:  Specifications  

2. Introduction 

2.1 Overview 

 

The Magenta MultiView Series extends video, audio and serial signals over ordinary 
Category 5 cable.  
 
This manual covers Magenta MultiView Series AK600 Receivers. These units are field 
configurable for various video, audio and serial options. See Appendix B for 
configuration settings. 
232 versions support full modem RS232 serial signals with the video. 
SA series feature video, stereo audio and RS-232 signals on a single cat5. 
SAP series units are similar to the above but have additional features for pollable serial. 
 
The Magenta MultiView Series AK600 Receivers feature optional integrated skew  
compensation that can be varied in 2 ns increments to 65 ns total per color channel to 
cancel the effects of skew in Category cables. This feature allows you to use CAT5e 
and reduced-skew CAT6 cables to lengths up to 600 ft.  
 
For information on the respective transmitter unit, please refer to the appropriate 
manual included with the transmitter. 
 
All models support refresh rates/resolutions of 1920x1200 to 600 feet (183 m). 

 

WARNING 

This equipment is not intended for, nor does it support, distribution 

through an Ethernet network. Do not connect these devices to any sort 

of networking or telecommunications equipment! 

 

2.2 Equipment You May Also Need 

 

• Audio cable with RCA jacks. 
• Video cable with HD15 connectors 
• Serial cable with DB9 connectors. 
• CAT5 cable. 

 

2.3 Compatible Cabling 

 

Magenta  Research products are compatible with Cat5/5e/6 data cabling as well as 
skew free CAT5/5e cabling manufactured for video applications. Note that some skew 
free Cat5 is specific to a particular vendor and is not compatible with our products. 
Please ensure any skew free CAT5 cable is non-proprietary prior to purchase/
installation. 
CAT6 cable, due to the manufacture method, can exhibit much greater skew than 
standard CAT5/5e and may require skew compensation beyond what the standard 
product offers. Please contact Magenta Research for assistance. 
CAT5/5e/6 cabling for the Magenta MultiView Series  must be pinned to the TIA-EIA 
T568B wiring specification (see appendix A)  We also highly recommend that all CAT5 
cables be pre-terminated and tested. Cables terminated on-site or in an existing 
infrastructure should be tested before use to ensure compliance with the TIA-EIA 
T568B specification. Using incorrectly terminated CAT5 cables can damage the 
Magenta MultiView Series. 

.

 

Summary of Contents for MultiView II AK600





























Reviews: