Magenta MULTIVIEW 250A Quick Reference & Setup Manual Download Page 3

 

 

1.Specifications 

 

Cable Required: 

Category 5, 5e, 6 shielded or unshielded twisted pair  

 
Compliance: 

CE; FCC Class A, IC Class/class A 

 
Video Support: 

to UXGA (1600x1200 @ 70Hz), RGBHV, RGB, Composite, S-

                             Video, Component Video modes 

 
Maximum  
Resolution and 
Refresh Rate:  

At 250 ft. (76 m) or less, 1600 x 1200 at 70 Hz 

 

Required Source 
Impedance: 

Video OUT: 75 ohms; 

                     Audio OUT (if any): 600 ohms maximum 
                       

Required Destination 
Impedance: 

Video IN: 75 ohms; 

                     Audio IN (if any): 600 ohms minimum 
 

Audio 
Characteristics: 

Channels:  Right/Left summed; 

                              Line Level 600 Ohm Unbalanced 
                           

Connectors: 

 (1) 3.5-mm, (1) RJ-45, (1) HD15 F 

 
Temperature 
Tolerance: 

Operating: 32 to 104°F (0 to 40°C); 

                    Storage: -4 to +140°F (-20 to +60°C) 

Humidity 
Tolerance: 

Up to 80% noncondensing 

 
Enclosure: 

Steel 

 
Power:  

+5 VDC @ 260 mA max 

             Consumption: 1.3 watts maximum 

 
Size: 

 0.88 "H x 3.12"W x 3.75"D (2.2 x 7.9 x 9.5 cm) 

 
Weight: 

0.56 lb. (0.26 kg) 

CHAPTER 1:  Specifications  

 

11 

2. Introduction 

2.1 Overview 
 

Magenta’s MultiView

 CAT5 Video System MultiView series extends VGA and 

audio signals over ordinary Category 5 cable.  
 
This manual covers the Magenta MultiView

 250A CAT5 Video System Series 

Receiver with Audio. 
 
For information on the respective transmitter unit, please refer to the appropriate 
manual included with the transmitter. 
 

WARNING 

This equipment is not intended for, nor does it support, distribution 

through an Ethernet network. Do not connect these devices to any sort 

of networking or telecommunications equipment! 

 

2.2 Equipment You May Also Need 

 

• 1/8” (3.5mm) Audio cable with RCA jacks. 
• Video cable with HD15 connectors. 
• CAT5 cable. 

 
2.3 Compatible Cabling 
 

CAT5 cabling for the MultiView

 Series must be pinned to the T568B wiring 

specification (see appendix A).  We also highly recommend that all CAT5 cables 
be pre-terminated and tested. Cables terminated on-site or in an existing 
infrastructure should be tested before use to ensure compliance with the T568B 
specification. Using incorrectly terminated CAT5 cables can damage the Magenta 
MultiView

 Series.

 

Summary of Contents for MULTIVIEW 250A








Reviews: