background image

Page 9 of 10

Disassembly Instructions

TAKE-DOWN TIP* 

● After collapsing the tent and gathering hub style frame together, spread excess tent material away 

from the frame and place it on it’s side. Start at the frame and roll it with pressure until it has reduced 

in size. Fold the rainfly and wrap the folded rainfly around the rolled tent. This will keep the tent tight 

and make it easier to place back into the carry bag.

● Remove all Stakes and store them in a small stakes bag.

● Detach gear loft by unhooking S-hooks from fabric loops, fold for storage. Remove divider curtain 

   by detaching toggles from fabric loop, fold for storage. 

● Detach S-hooks and Velcro tapes that hold down rainfly, fold rainfly storage.

● Unfasten clips from the tent poles.

● Remove the frame from the pin-ring at the bottom of the tent. Knock down the frame by removing 

   all poles from plastic molds.

● Lay the tent flat and check, folding all the poles.

● The tent is folded vertically 4-5 times to make the width of the tent consistent with the outer bag.

● Place the folded outer account over the folded inner account.

● Put the stakes bag on the inside and outside of the tent, then roll up the whole tent with the pole 

   bag as the axis and tie it up with the bandage.

● Put the rolled tent in the outer bag together with the stakes bag.

Care and Maintenance

•  Your product must be stored dry. One of the easiest ways to damage your product is by storing it 
  while it is wet. Storing a wet tent as short as 24 hours in warm weather is likely to cause mildew on 

the fabric coatings.

•  If you must close camp in the rain, open your product and set it up to allow it to dry as soon as
  possible. Allow dirt to dry on the fabric after a rainfall before lightly sweeping it off with a brush.
  For tougher stains, spray the area with water and lightly wipe it off with a few strokes. Do not use 
  washer or dryer. 

DO NOT SCRUB THE FABRIC. ALWAYS MAKE SURE THE TENT IS COMPLETELY  

  DRY BEFORE REPACKING.

•  This tent is made from synthetic fabric that has been treated and is highly resistant to the sun’s
  Ultraviolet (U

V

) light. However, no fabric can withstand prolonged 

expo

sure to sunlight. Do not leave  

 

your tent set up for weeks at a time. Exposure to ultraviolet rays from the sun can damage and/or  

  discolor the material.

•  The tent is water repellent. It is not waterproof. During heavy or continuous rain, some leakage may 
  occur. Avoid contact between objects and the inside wall or roof of the tent, as this may result in  
  leakage at points of contact. In the event of seam leakage, apply a seam sealer compound.

•  Do not spray or apply insecticide or pesticide on your product

. It may damage UV resistant or water  

  repellent properties of this product.

•  Clean the poles with a cloth and lubricate them with a silicone spray to help prevent corrosion and  
  keep from being gritty. This is especially important after using the product around salt water.

•  Store the stakes in a separate storage bag. Do not pack the stakes inside the tent.

Summary of Contents for FSMGCT2009











Reviews: